Hostname: page-component-77c89778f8-cnmwb Total loading time: 0 Render date: 2024-07-24T08:18:05.089Z Has data issue: false hasContentIssue false
  • English
  • Français

Effect of operating parameters on the drilling behavior of Zr57.5Cu11.2Ni13.8Al17.5 bulk metallic glass

Published online by Cambridge University Press:  20 November 2013

Naeem ul Haq Tariq ,
Ghulam Muhammad  and
Hasan Bin Awais
Naeem ul Haq Tariq*
Affiliation:
Department of Metallurgy and Materials Engineering, Pakistan Institute of Engineering and Applied Sciences, Nilore, Islamabad, Pakistan
Ghulam Muhammad
Affiliation:
Department of Mechanical Engineering, Pakistan Institute of Engineering and Applied Sciences, Nilore, Islamabad, Pakistan
Hasan Bin Awais
Affiliation:
Department of Metallurgy and Materials Engineering, Pakistan Institute of Engineering and Applied Sciences, Nilore, Islamabad, Pakistan
*
a)Address all correspondence to this author. e-mail: naeem421@hotmail.com
Get access

Abstract

Zr-based bulk metallic glasses (BMGs) exhibit superior physical and chemical properties in comparison to their crystalline counterparts. In the present work, drilling behavior of Zr57.5Cu11.2Ni13.8Al17.5 BMG was investigated at various operating conditions. Drilling was performed using high-speed steel (HSS) and carbide bits. Chip morphology, chip light emission, and burr formation at various drilling parameters were studied to achieve a feasible operating condition for drilling hole without light emission, chip clogging, and debris accumulation. Short spiral chip morphology which is considered ideal in the drilling process was observed at relatively low feed rate (1.5 mm/min) and medium spindle speed (1500 rpm). This also resulted in a small amount of molten debris around the entry hole. It was observed that at the same feed rate, the gradual increase in the speed of the HSS drill bit results in more light emission from the machining surface, whereas no light emission was observed in the case of the carbide drill bit at all drilling parameters.

Type
Articles
Information
Journal of Materials Research , Volume 28 , Issue 23 , 14 December 2013 , pp. 3288 - 3296
Copyright
Copyright © Materials Research Society 2013 

Access options

Get access to the full version of this content by using one of the access options below. (Log in options will check for institutional or personal access. Content may require purchase if you do not have access.)

References

REFERENCES

Johnson, W.: Bulk glass-forming metallic alloys: Science and technology. MRS Bull. 24, 42–56 (1999).Google Scholar
Trexler, M.M. and Thadhani, N.N.: Mechanical properties of bulk metallic glasses. Prog. Mater. Sci. 55, 759–839 (2010).Google Scholar
Yavari, A.R., Lewandowski, J.J., and Eckert, J.: Mechanical properties of bulk metallic glasses. MRS Bull. 32, 635–638 (2007).Google Scholar
Suryanarayana, C.: Electrical properties and applications. In Metallic Glasses: Production, Properties and Applications, Anantharaman, T.R. ed.; Trans Tech Publications: Aedermannsdorf, Switzerland, 1984; pp. 249–267.Google Scholar
Schuh, C.A., Hufnagel, T.C., and Ramamurty, U.: Mechanical behavior of amorphous alloys. Acta Mater. 55, 4067–4109 (2007).Google Scholar
Eckert, J., Das, J., Pauly, S., and Duhamel, C.: Mechanical properties of bulk metallic glasses and composites. J. Mater. Res. 22, 285–301 (2007).Google Scholar
Fujita, K., Morishita, Y., Nishiyama, N., Kimura, H., and Inoue, A.: Cutting characteristics of bulk metallic glass. Mater. Trans. 46, 2856–2863 (2005).Google Scholar
Jiang, M.Q. and Dai, L.H.: Formation mechanism of lamellar chips during machining of bulk metallic glass. Acta Mater. 57, 2730–2738 (2009).Google Scholar
Bakkal, M., Shih, A.J., McSpadden, S.B., Liu, C.T., and Scattergood, R.O.: Light emission, chip morphology, and burr formation in drilling the bulk metallic glass. Int. J. Mach. Tools Manuf. 45, 741–752 (2005).Google Scholar
Bakkal, M., Shih, A.J., McSpadden, S.B., and Scattergood, R.O.: Thrust force, torque, and tool wear in drilling the bulk metallic glass. Int. J. Mach. Tools Manuf. 45, 863–872 (2005).CrossRefGoogle Scholar
Tariq, N.H., Hassan, B.A., Akhter, J.I., and Ali, F.: Mechanical and tribological properties of Zr-Al-Ni-Cu bulk metallic glasses. J. Alloys Compd. 469, 179 (2009).Google Scholar
Bakkal, M., Liu, C.T., Watkins, T.R., Scattergood, R.O., and Shih, A.J.: Oxidation and crystallization of Zr-based bulk metallic glass due to machining. Intermetallics 12, 195–204 (2004).Google Scholar
Bakkal, M., Shih, A.J., Scattergood, R.O., and Liu, C.T.: Machining of a Zr–Ti–Al–Cu–Ni metallic glass. Scr. Mater. 50, 583–588 (2004).CrossRefGoogle Scholar
Bakkal, M., Shih, A.J., and Scattergood, R.O.: Chip formation, cutting forces, and tool wear in turning of Zr-based bulk metallic glass. Int. J. Mach. Tools Manuf. 44, 915–925 (2004).CrossRefGoogle Scholar
Lopez de lacalle, L.N., Perez, J., Llorente, J.I., and Sanchez, J.A.: Advanced cutting conditions for the milling of aeronautical alloys. J. Mater. Process. Technol. 100, 1–11 (2000).Google Scholar
Batzer, S.A., Haan, D.M., Rao, P.D., Olson, W.W., and Sutherland, J.W.: Chip morphology and hole surface texture in the drilling of cast aluminum alloys. J. Mater. Process. Technol. 79, 72–78 (1998).CrossRefGoogle Scholar
Ke, F., Ni, J., and Stephenson, D.A.: Continuous chip formation in drilling. Int. J. Mach. Tools Manuf. 45, 1652–1658 (2005).Google Scholar
Dornfeldl, D.A., Kim, J.S., Dechow, H., Hewson, J., and Chen, L.J.: Drilling burr formation in titanium alloy, Li-6AI-4V. CIRP Ann. 48, 73–76 (1999).Google Scholar
Ko, S.L. and Lee, J.K.: Analysis of burr formation in drilling with a new concept drill. J. Mater. Process. Technol. 113, 392–398 (2001).Google Scholar