Hostname: page-component-5c6d5d7d68-pkt8n Total loading time: 0 Render date: 2024-08-07T11:16:06.613Z Has data issue: false hasContentIssue false
  • English
  • Français

Fabrication of near-net-shape Al2O3-fiber-reinforced Ni3Al composites by combustion synthesis

Published online by Cambridge University Press:  03 March 2011

William C. Williams  and
Gregory C. Stangle
William C. Williams
Affiliation:
Institute for Self-Propagating High-Temperature Synthesis, New York State College of Ceramics at Alfred University, Alfred. New York 14802
Gregory C. Stangle
Affiliation:
Institute for Self-Propagating High-Temperature Synthesis, New York State College of Ceramics at Alfred University, Alfred. New York 14802
Get access

Abstract

In this paper, a one-step, combustion synthesis-based process for fabricating Al2O3 fiber-reinforced Ni3Al is described. The process uses relatively low temperatures and pressures, and can be used to prepare relatively large, dense, near-net-shape articles that possess either simple or relatively complicated shapes. This process can be used to incorporate continuous, aligned fibers into the Ni3Al matrix material in such a way that the fibers are not damaged either mechanically (due to relatively small loads applied during the process) or chemically (due to the very short time at which the sample remains at elevated tempertures during the process). (Chopped fibers, as well as equiaxed particles or whiskers, could also be similarly incorporated using this process.) This combustion synthesis process is a relatively simple one-requiring only relatively low temperatures and pressures, as well as relatively low-cost starting materials-which suggests that its scale-up beyond the laboratory scale would be particularly straightforward.

Type
Articles
Information
Journal of Materials Research , Volume 10 , Issue 7 , July 1995 , pp. 1736 - 1745
Copyright
Copyright © Materials Research Society 1995

Access options

Get access to the full version of this content by using one of the access options below. (Log in options will check for institutional or personal access. Content may require purchase if you do not have access.)

References

REFERENCES

1Darolia, R., JOM 3, 44–49 (1991).CrossRefGoogle Scholar
2Tien, J. K., Eng, S., and Sanchez, J.M., in High-Temperature Ordered Intermetallic Alloys II, edited by Stoloff, N. S., Koch, C. C., Liu, C. T., and Izumi, O. (Mater. Res. Soc. Symp. Proc. 81, Pittsburgh, PA, 1987), pp. 183–193.Google Scholar
3Krueger, D. D., Marquardt, B. J., and Field, R. D., in High Temperature Ordered Intermetallic Alloys II edited by Stoloff, N. S., Koch, C. C., Liu, C. T., and Izumi, O. (Mater. Res. Soc. Symp. Proc. 81, Pittsburgh, PA, 1987), pp. 309–314.Google Scholar
4Anton, D. L., in High Temperature/High-Performance Composites, edited by Lemkey, F.D., Evans, A. G., Fishman, S. G., and Strife, J.R. (Mater. Res. Soc. Symp. Proc. 120, Pittsburgh, PA, 1988), pp. 57–67.Google Scholar
5Brennan, P. C., Kao, W. H., and Jeng, S. M., in Intermetallic MatrixComposites, edited by Anton, D.L., Martin, P. L., Miracle, D. B., and McMeeking, R. (Mater. Res. Soc. Symp. Proc. 194, Pittsburgh, PA, 1990), pp. 169–174.Google Scholar
6Williams, W. C., B. S. Thesis, Alfred University (1994).Google Scholar
7McKamey, C.G. and Lee, E. H., in Intermetallic Matrix Composites, edited by Anton, D.L., Martin, P. L., Miracle, D. B., and McMeeking, R. (Mater. Res. Soc. Symp. Proc. 194, Pittsburgh, PA, 1990), pp. 163–168.Google Scholar
8Bose, A., Moore, B., German, R. M., and Stoloff, N.S., JOM 40(9), 14–17 (1988).CrossRefGoogle Scholar
9Lebrat, J. P., Varma, A., and Miller, A. E., Metall. Trans. A 23A, 69–76 (1992).CrossRefGoogle Scholar
10Mukherjee, S. K. and Khanra, G. P., J. Mater. Sci. Lett. 10, 1222–1224 (1991).CrossRefGoogle Scholar
11Stoloff, N. S. and Alman, D. E., in Intermetallic Matrix Composites, edited by Anton, D. L., Martin, P. L., Miracle, D. B., and McMeeking, R. (Mater. Res. Soc. Symp. Proc. 194, Pittsburgh, PA, 1990), pp. 31–43.Google Scholar
12Anton, D. L. and Shah, D. H., in High Temperature Ordered Intermetallic Alloys III, edited by Liu, C. T., Taub, A. I., Stoloff, N. S., and Koch, C. C. (Mater. Res. Soc. Symp. Proc. 133, Pittsburgh, PA, 1987), pp. 361–371.Google Scholar
13Persad, C., Raghunathan, S., Lee, B. H., Bourell, D. L., Eliezer, Z., and Marcus, H. L., in High Temperature/High-Performance Composites, edited by Lemkey, F. D., Evans, A. G., Fishman, S. G., and Strife, J.R. (Mater. Res. Soc. Symp. Proc. 120, Pittsburgh, PA, 1988), pp. 23–28.Google Scholar
14Rigney, J. D., Khadkikar, P. S., Lewandowski, J. J., and Vedula, K., in High Temperature Ordered Intermetallic Alloys III, edited by Liu, C.T., Taub, A. I., Stoloff, N. S., and Koch, C.C. (Mater. Res. Soc. Symp. Proc. 133, Pittsburgh, PA, 1987), pp. 603–608.Google Scholar
15Sikka, V. K., in High-Temperature Ordered Intermetallic Alloys II, edited by Stoloff, N.S., Koch, C. C., Liu, C. T., and Izumi, O. (Mater. Res. Soc. Symp. Proc. 81, Pittsburgh, PA, 1987), pp. 487–493.Google Scholar
16German, R. M., Bose, A., and Stoloff, N.S., in High Temperature Ordered Intermetallic Alloys III, edited by Liu, C.T., Taub, A. I., Stoloff, N. S., and Koch, C.C. (Mater. Res. Soc. Symp. Proc. 133, Pittsburgh, PA, 1987), pp. 403–414.Google Scholar
17Sen, S. and Stefanescu, D., JOM 43, 30–34 (1991).CrossRefGoogle Scholar
18Munir, Z. A., Am. Ceram. Soc. Bull. 67, 342–349 (1988).Google Scholar
19Philpot, K. A., Munir, Z. A., and Holt, J.B., J. Mater. Sci. 22, 159–169 (1987).CrossRefGoogle Scholar
20Rabin, B. H., Bose, A., and German, R.M., in Combustion and Plasma Synthesis of High-Temperature Materials, edited by Munir, Z. A. and Holt, J.B. (VCH, New York, 1990), pp. 114–121.Google Scholar
21Golubjatnikov, K. A., Stangle, G. C., and Spriggs, R.M., Am. Ceram. Soc. Bull. 72(12), 96–102 (1993).Google Scholar
22Mistier, R. E., Shanefield, D. J., and Bunk, R.B., in Ceramic Processing Before Firing, edited by Onoda, G. Y. Jr. and Hench, L. L. (John Wiley, New York, 1978), pp. 411–448.Google Scholar
231990 Annual Book of ASTM Standards, edited by Storer, R.A. (American Society for the Testing of Materials, Philadelphia, PA, 1990), Vol. 15.02, pp. 112–113.Google Scholar
24Niedzialek, S. E., Stangle, G. C., and Kaieda, Y., J. Mater. Res. 8, 2026–2034 (1993).CrossRefGoogle Scholar
25Zhang, Y. and Stangle, G. C., J. Mater. Res. 9, 2605–2619 (1994).CrossRefGoogle Scholar
26Zhang, Y. and Stangle, G. C., J. Mater. Res. 10, 1828–1845(1995).CrossRefGoogle Scholar
27Zhang, Y., Ph.D. Dissertation, Alfred University (1994).Google Scholar