Hostname: page-component-7479d7b7d-k7p5g Total loading time: 0 Render date: 2024-07-11T16:26:59.606Z Has data issue: false hasContentIssue false
  • English
  • Français

Glass-forming ability of Pr–(Cu,Ni)–Al alloys in eutectic system

Published online by Cambridge University Press:  31 January 2011

Y. Zhang ,
H. Tan ,
H. Z. Kong ,
B. Yao  and
Y. Li
Y. Zhang*
Affiliation:
AMM&NS, Singapore-Massachusetts Institute of Technology Alliance, National University of Singapore, Singapore 117576
H. Tan
Affiliation:
Department of Materials Science, Faculty of Sciences, National University of Singapore, Singapore 119260
H. Z. Kong
Affiliation:
Department of Materials Science, Faculty of Sciences, National University of Singapore, Singapore 119260
B. Yao
Affiliation:
Department of Materials Science, Faculty of Sciences, National University of Singapore, Singapore 119260
Y. Li
Affiliation:
AMM&NS, Singapore-MIT Alliance, National University of Singapore, Singapore 117576, and Department of Materials Science, Faculty of Sciences, National University of Singapore, Singapore 119260
*
a)Address all correspondence to this author. e-mail: smazy@nus.edu.sg
Get access

Abstract

A eutectic point in Pr-rich Pr-(Cu,Ni)-Al alloys was experimentally determined by measuring the solidus temperature (Tm) and liquidus temperature (T1). It was found that Pr68(Cu0.5Ni0.5)25Al7 (at.%) is at the eutectic composition in the pseudoternary Pr–(Cu0.5Ni0.5)–Al alloys. The alloy Pr68(Cu0.5Ni0.5)25Al7 exhibits better glass-forming ability (GFA) than the ternary eutectic alloy Pr68Cu25Al7. However, the best GFA was obtained at an off-eutectic composition (Pr54[Cu0.5Ni0.5]30Al16) in the Pr–(Cu0.5Ni0.5)–Al alloys, which can be formed in fully amorphous rods with diameter of 1.5 mm by copper mold casting. Moreover, the glass-transition temperature Tg increases quickly (from 367 to 522 K) with the increasing of the Al content (from 3 to 27 at.%). The deviation of the best GFA composition from the eutectic point [Pr68(Cu0.5Ni0.5)25Al7] was explained in terms of the asymmetric coupled eutectic zone, the competition between growth of crystalline phase and formation of amorphous, and the higher glass-transition temperature Tg on the hypereutectic side.

Type
Articles
Information
Journal of Materials Research , Volume 18 , Issue 3 , March 2003 , pp. 664 - 671
Copyright
Copyright © Materials Research Society 2003

Access options

Get access to the full version of this content by using one of the access options below. (Log in options will check for institutional or personal access. Content may require purchase if you do not have access.)

References

REFERENCES

1.Johnson, W.L., MRS Bull. 20(10), 42 (1999).CrossRefGoogle Scholar
2.Inoue, A., Acta Mater. 48, 279 (2000).CrossRefGoogle Scholar
3.Li, Y., Mater. Trans. 42, 556 (2001).CrossRefGoogle Scholar
4.Inoue, A., Takeuchi, A., and Shen, B., Mater. Trans. 42, 970 (2001).CrossRefGoogle Scholar
5.Lu, Z.P., Goh, T.T., Li, Y., and Ng, S.C., Acta Mater. 47, 2215 (1999).CrossRefGoogle Scholar
6.Fan, G.J., Loeser, W., Roth, S., Eckert, J., and Schultz, L., J. Mater. Res. 15, 1556 (2000).CrossRefGoogle Scholar
7.Hays, C.C., Schroers, J., and Johnson, W.L., Appl. Phys. Lett. 79, 1605 (2001)CrossRefGoogle Scholar
8.Zhang, Y., Zhao, D.Q., Wei, B.C., Wen, P., Pan, M.X., Wang, W.H., J. Mater. Res. 16, 1675 (2001).CrossRefGoogle Scholar
9.Lu, Z.P., Tan, H., Li, Y., and Ng, S.C., Scripta Mater. 42, 667 (2000).CrossRefGoogle Scholar
10.Tan, H., Lu, Z.P., Yao, H.B., Feng, Y.P., and Li, Y., Mater. Trans. 42, 268 (2001).Google Scholar
11.Boettinger, W.J., in Rapidly Solidified Amorphous and Crystalline Alloys, edited by Kear, B.H., Giessen, B.C., and Cohen, M. (Elsevier Science, London, U.K., 1982), p. 99.Google Scholar
12.Zhang, Y., Yao, B., Tan, H., and Li, Y., J. Alloys Comps. 333(1–2), 113 (2002).CrossRefGoogle Scholar
13.Chen, H.S., Acta Metall. 22, 1505 (1974).Google Scholar
14.Glade, S.C., Busch, R., Lee, D.S., and Johnson, W.L., J. Appl. Phys. 87, 7242 (2000).CrossRefGoogle Scholar
15.Lu, Z.P., Hu, X., and Li, Y., Intermetallics 8, 477 (2000).CrossRefGoogle Scholar
16.Thompson, C.V. and Spaepen, F., Acta Metall. 27, 1855 (1979).CrossRefGoogle Scholar
17.Fecht, H.J., Mater. Sci. Eng. A133, 443 (1991).CrossRefGoogle Scholar
18.Fundamentals of Solidification, 4th ed., edited by Kurz, W., Fisher, D.J. (Trans Tech, Switzerland, 1998), p. 150.Google Scholar
19.He, Y., Dougherty, G.M., Shiflet, G.J., and Poon, S.J., Acta Metall. and Mater. 41, 337 (1993).CrossRefGoogle Scholar
20.Hong, S.Y., Guo, W.H., and Kui, H.W., J. Mater. Res. 14, 3668 (1999).CrossRefGoogle Scholar
21.Molokanov, V.V., Petrzhik, M.I., Mikhailova, T.N., and Sviridova, T.A., J. Non-Cryst. Solids 250–252, 560 (1999).CrossRefGoogle Scholar