Hostname: page-component-5c6d5d7d68-ckgrl Total loading time: 0 Render date: 2024-08-14T17:37:45.308Z Has data issue: false hasContentIssue false
  • English
  • Français

Mechanical properties of niobium disulfide and its hydrated sodium cation intercalation compound

Published online by Cambridge University Press:  31 January 2011

C. M. Lepienski ,
M. S. Meruvia ,
W. Veiga  and
F. Wypych
C. M. Lepienski
Affiliation:
Departamento de Física, Universidade Federal do Paraná, Caixa Postal 19081, 81531–990 Curitiba-PR, Brazil
M. S. Meruvia
Affiliation:
Departamento de Física, Universidade Federal do Paraná, Caixa Postal 19081, 81531–990 Curitiba-PR, Brazil
W. Veiga
Affiliation:
Departamento de Física, Universidade Federal do Paraná, Caixa Postal 19081, 81531–990 Curitiba-PR, Brazil
F. Wypych
Affiliation:
Departamento de Química, Universidade Federal do Paraná, Caixa Postal 19081, 81531–990 Curitiba-PR, Brazil
Get access

Abstract

Mechanical properties of 2H–NbS2 and its intercalation derivative Nax(H2O)yNbS2 were measured by using nanoindentation techniques. The intercalation chemical process was conducted in solution and the cation–hydrated derivative produced was [Nax(H2O)yNbS2]. It was observed that the intercalation process occurs through the crystal edges producing a wave intercalation's front that moved as the reaction proceeded. The hardness and elastic modulus presented very low values in the intercalated region. The load × displacement curves from nanoindentation tests suggested that intercalation of hydrated sodium ions through the edges caused layer separation even in the nonintercalated region at the center of the crystal. It is important to emphasize that no similar studies were found in the literature about this theme. Intercalation process is very important in several areas, like solid-state batteries, and mechanical properties of these kinds of materials are not completely understood. This study is a new approach to understanding the mechanical behavior of layered materials submitted to an intercalation process.

Type
Rapid Communications
Information
Journal of Materials Research , Volume 15 , Issue 10 , October 2000 , pp. 2061 - 2064
Copyright
Copyright © Materials Research Society 2000

Access options

Get access to the full version of this content by using one of the access options below. (Log in options will check for institutional or personal access. Content may require purchase if you do not have access.)

References

REFERENCES

1. Subba Rao, G.V. and Shafer, M.V., in Intercalated Layered Materials, edited by Levy, F. (D. Riedel Publishing, Dordrecht, 1979), Vol. 6, p. 99.Google Scholar
2. Müller-Warmuth, W. and Schöllhorn, R., in Progress in Intercalation Research (Kluwer Academic Publishing, Dordrecht, 1994), p. 1.Google Scholar
3. Wypych, F., Gomes, M.A.B, Denicoló, I., and Adad, L.B., J. Elect. Soc. 143, 2522 (1996).CrossRefGoogle Scholar
4. Lerf, A. and Schöllhorn, R., Inorg. Chem. 16, 2950 (1977).CrossRefGoogle Scholar
5. Oliver, W.C. and Pharr, G.M., J. Mater. Res. 7, 1564 (1992).CrossRefGoogle Scholar
6. Bobji, M.S. and Biswas, S.K., J. Mater. Res. 14, 2259 (1999).CrossRefGoogle Scholar
7. Pharr, G.M., Oliver, W.C., and Brotzen, F., J. Mater. Res. 7, 613 (1992).Google Scholar
8. Nix, W.D., Mater. Sci. Eng. A 234–236, 37 (1997).CrossRefGoogle Scholar
9. Corcoran, S.G., Colton, R.J., Lilleodden, E.T., and Gerberich, W.W., Phys. Rev. B 55, R16057 (1997).Google Scholar
10. Mann, A.B. and Pethica, J.B., Philos. Mag. A 79, 577 (1999).CrossRefGoogle Scholar
11. Ma, X., Unertl, W.N., and Erdermir, A., J. Mater. Res. 14, 3455 (1999).CrossRefGoogle Scholar