Hostname: page-component-84b7d79bbc-7nlkj Total loading time: 0 Render date: 2024-07-30T13:26:41.550Z Has data issue: false hasContentIssue false
  • English
  • Français

Effects of Processing on Fiber/Matrix Interfaces in Ni3Al/Sapphire Single Crystal Composites

Published online by Cambridge University Press:  15 February 2011

D. Ringer  and
C. L. White
D. Ringer
Affiliation:
Michigan Technological University, Department of Metallurgical and Materials Engineering, Houghton, MI 49931-1295, USA
C. L. White
Affiliation:
Michigan Technological University, Department of Metallurgical and Materials Engineering, Houghton, MI 49931-1295, USA
Get access

Abstract

Composites consisting of Ni3Al modified with Zr, Fe, and B (IC-50) reinforced with continuous sapphire single crystal fibers have been prepared by vacuum hot pressing foil/fiber multilayers. Previous research detected formation of Zr-rich precipitates and sulfur segregation at fiber/matrix interfaces in these materials subsequent to fabrication. In this work, fiber bonding to the Ni3Al matrix has been characterized using fiber push-out tests. Segregation and precipitation at fiber/matrix interfaces has been examined using scanning Auger electron spectroscopy and scanning electron microscopy. For comparison, composites have also been prepared from Ni, Ni-Al, and Ni-Al-Zr solid solution matrices, to evaluate the effects of matrix strength and reactivity on processing and fiber/matrix reactions.

Type
Research Article
Information
MRS Online Proceedings Library (OPL) , Volume 350: Symposium U – Intermetallic Matrix Composites III , 1994 , 125
Copyright
Copyright © Materials Research Society 1994

Access options

Get access to the full version of this content by using one of the access options below. (Log in options will check for institutional or personal access. Content may require purchase if you do not have access.)

References

1. Schneibel, J.H., George, E.P., McKamey, C.G., Ohriner, E.K., Santella, M.L., and Carmichael, C.A., J. Mater. Res. 6 (8), 1673–79 (1991).Google Scholar
2. McKamey, C.G. and Lee, E.H. in intermetallic Matrix Composites, edited by Anton, D.L., Martin, P.L., Miracle, D.B., and McMeeking, R. (Mater. Res. Soc. Proc. 194, Pittsburgh, PA, 1990) pp. 163–68.Google Scholar
3. Noebe, R.D., Bowman, R.R., and Eldridge, J.I. in Intermetallic Matrix Composites, edited by Anton, D.L., Martin, P.L., Miracle, D.B., and McMeeking, R. (Mater. Res. Soc. Proc. 194, Pittsburgh, PA, 1990) pp. 323–331.Google Scholar
4. McLean, Malcolm in High Temperature/High Performance Composites, edited by Lemkey, F.D., Fishman, S.G., Evans, A.G., and Strife, J.R. (Mater. Res. Soc. Proc. 120, Pittsburgh, PA, 1988) pp. 67–79.Google Scholar
5. Ringer, D. and White, C.L., Intermetallics 1, 127–137 (1993).Google Scholar
6. Koss, D.A., Kallas, M.N., and Hellmann, J.R. in Intermetallic Matrix Composites II, edited by Miracle, D.B., Anton, D.L., Graves, J.A. (Mater. Res. Soc. Proc. 273, Pittsburgh, PA, 1992) pp. 303–313.Google Scholar
7. Ringer, D. and White, C.L. in Processing and Fabrication of Advanced Materials for High Temperature Applications II, edited by Ravi, V.A. and Srivatsan, T.S. (The Minerals, Metals & Materials Society, Warrendale PA, 1993) pp. 487–499.Google Scholar
8. Baik, S., and White, C.L., J. Am. Ceram. Soc. 70 (9), 682–88 (1987).Google Scholar
9. Levin, E.M. and McMurdie, H.F., Phase Diagrams for Ceramists 1975 Supplement (Figure 4313) (The American Ceramic Society, Inc., 1975) p. 105.Google Scholar
10. Perkin Elmer 660 SAM System, Technical Manual Part No. 617678, Physical Electronics Division, Eden Prairie, MN.Google Scholar