Hostname: page-component-84b7d79bbc-lrf7s Total loading time: 0 Render date: 2024-07-27T23:20:17.393Z Has data issue: false hasContentIssue false
  • English
  • Français

Evaluation of Tensile Static, Dynamic, and Cyclic Fatigue Behavior for A Hiped Silicon Nitride at Elevated Temperatures

Published online by Cambridge University Press:  25 February 2011

Chih-Kuang Jack Lin ,
Michael G. Jenkins  and
Matitison K. Ferber
Chih-Kuang Jack Lin
Affiliation:
Metals and Ceramics Division, Oak Ridge National Laboratory, Oak Ridge, TN 37831-6064
Michael G. Jenkins
Affiliation:
Metals and Ceramics Division, Oak Ridge National Laboratory, Oak Ridge, TN 37831-6064
Matitison K. Ferber
Affiliation:
Metals and Ceramics Division, Oak Ridge National Laboratory, Oak Ridge, TN 37831-6064
Get access

Abstract

Tensile fatigue behavior of a hot-isostatically-pressed (HIPed) silicon nitride was investigated over ranges of constant stresses, constant stress rates, and cyclic loading at 1150-1370°C. At 1150°C, static and dynamic fatigue failures were governed by a slow crack growth mechanism. Creep rupture was the dominant failure mechanism in static fatigue at 1260 and 1370°C. A transition of failure mechanism from slow crack growth to creep rupture appeared at stress rates ≤10−2 MPa/s for dynamic fatigue at 1260 and 1370°C. At 1 150-1370°C, cyclic loading appeared to be less damaging than static loading as cyclic fatigue specimens displayed greater failure times than static fatigue specimens under the same maximum stresses.

Type
Research Article
Information
MRS Online Proceedings Library (OPL) , Volume 287: Symposium K – Silicon Nitride Ceramics–Scientific and Technological Advances , 1992 , 455
Copyright
Copyright © Materials Research Society 1993

Access options

Get access to the full version of this content by using one of the access options below. (Log in options will check for institutional or personal access. Content may require purchase if you do not have access.)

References

REFERENCES

1. Wiederhorn, S.M. and Fuller, E.R. Jr., Mater. Sci. Eng. 71, 169 (1985).Google Scholar
2. Wiederhorn, S.M., in Fracture Mechanics of Ceramics, Vol. 2, edited by Bradt, R.C. et al. (Plenum Press, New York, 1974), p. 623.Google Scholar
3. Ritter, J.E., in Fracture Mechanics of Ceramics, Vol. 4, edited by Bradt, R.C. et al. (Plenum Press, New York, 1978), p. 667.Google Scholar
4. Evans, A.G. and Fuller, E.R., Met. Trans. 5, 27 (1974).Google Scholar
5. Ferber, M.K. and Jenkins, M.G., J. Am. Ceram. Soc. 75, 2453 (1992).Google Scholar
6. Becher, P.F., Angelini, P., Warwick, W.H., and Tiegs, T.N., J. Am. Ceram. Soc. 73, 91 (1990).Google Scholar
7. Quinn, G.D., J. Mater. Sci. 25, 4361 (1990).Google Scholar
8. Horibe, S., J. Eur. Ceram. Soc. 6, 89 (1990).Google Scholar
9. Dauskardt, R.H., Marshall, D.B., and Ritchie, R.O., J. Am. Ceram. Soc. 73, 893 (1990).Google Scholar
10. Fett, T., Himsolt, G., and Munz, D., Adv. Ceram. Mater. 1, 179 (1986).Google Scholar
11. Han, L.X. and Suresh, S., J. Am. Ceram. Soc. 72, 1233 (1989).Google Scholar
12. Lin, C.-K.J. and Socie, D.F., J. Am. Ceram. Soc. 74, 1511 (1991).Google Scholar
13. Lin, C.-K.J., Socie, D.F., Xu, Y., and Zangvil, A., J. Am. Ceram. Soc. 75, 637 (1992).Google Scholar