Hostname: page-component-5c6d5d7d68-wpx84 Total loading time: 0 Render date: 2024-09-01T07:22:00.439Z Has data issue: false hasContentIssue false
  • English
  • Français

Internal Hydrogen Effects in Ti Code 12 Overpack/Cannister Material

Published online by Cambridge University Press:  21 February 2011

Neville Moody  and
Steve Robinson
Neville Moody
Affiliation:
Sandia National Laboratories, Livermore, California 94550
Steve Robinson
Affiliation:
Sandia National Laboratories, Livermore, California 94550
Get access

Abstract

The effects of internal hydrogen on the mechanical properties of Ti Code 12 were studied by gas phase charging smooth bar tensile samples. Tensile tests showed no change in yield strength with increasing hydrogen concentration. A slight decrease in ductility and fracture stress at hydrogen concentrations above 200 wppm accompanied by secondary cracking along grain boundaries indicated embrittlement. At hydrogen concentrations near and above 400 wppm, cleavage fracture associated with strain-induced hydrides was also observed.

Type
Research Article
Information
MRS Online Proceedings Library (OPL) , Volume 15: Symposium D – Scientific Basis for Nuclear Waste Management VI , 1982 , 753
Copyright
Copyright © Materials Research Society 1983

Access options

Get access to the full version of this content by using one of the access options below. (Log in options will check for institutional or personal access. Content may require purchase if you do not have access.)

References

REFERENCES

1. Braithwaite, J. W. and Molecke, M. A., Nuclear and Chemical Waste Management 1, 37 (1980)Google Scholar
2. Covington, L. C., Metal Progress 111, No. 2, 38 (1977).Google Scholar
3. Abrego, L. and Rack, H. J., The Slow Strain Rate Behavior of Ti Code 12 (ASTM Gr. 12) in Aqueous Chloride Solutions, SAND80–1728C, Sandia National Laboratories, Albuquerque, NM (1980).Google Scholar
4. Diegle, R. and Ruppen, J. A., a paper in these proceedings.Google Scholar
5. Petit, J. A., Chatainier, G., Lafargue, and Dabosi, F. in, Titanium'80 Science and Technology, Kimura, H. and Izumi, O. eds. (TMS-AIME, New York 1980), pp. 2659–2667.Google Scholar
6. Ruppen, J. A. and Headly, T., Sandia National Laboratories, Albuquerque, NM, private communication.Google Scholar
7. Williams, D. N., Schwartzberg, F.R. and Jaffee, R. I., Trans. ASM 51, 802 (1959).Google Scholar
8. Jaffee, R. I. and Williams, D. N., Trans. ASM 51, 820 (1959).Google Scholar
9. Paton, N. E. and Williams, J. C. in, Effect of Hydrogen on Behavior of Materials, Thompson, A. W. and Bernstein, I. M. eds., (TMS-AIME, New York 1976), pp. 409–432.Google Scholar
10. Moody, N. R. and Gerberich, W. W., Met. Trans. A 13A, 1055 (1982).Google Scholar
11. Jaffee, R. I., Progress in Metal Physics 7, 65 (1958).Google Scholar
12. Hall, I. W. and Hammond, C., Metal Sci. 12, 339 (1978).Google Scholar
13. Moody, N. R. and Gerberich, W. W., Fat. Eng. Mat. and Structures 5, 57 (1982).Google Scholar
14. Banerjee, D. and Arunachalam, V. S., Acta. Met. 29, 1685 (1981).Google Scholar
15. Rhodes, C. G. in, Titanium '80 Science and Technology, Kimura, H. and Izumi, O. eds. (TMS-AIME, New York 1980), pp. 1691–1700.Google Scholar
16. Buchner, V. H., Gutjahr, M. A., Beceu, K.-D. and Saufferer, H., Z. Metallk. 63, 497 (1972).Google Scholar