Hostname: page-component-848d4c4894-xfwgj Total loading time: 0 Render date: 2024-07-03T13:27:28.130Z Has data issue: false hasContentIssue false
  • English
  • Français

Microwave Sintering of Continuous Zirconia Ceramic Fibers

Published online by Cambridge University Press:  15 February 2011

Gerald. J. Vogt ,
Wesley. P. Unruh  and
Ross. H. Plovnick
Gerald. J. Vogt
Affiliation:
Los Alamos National Laboratory, P.O. Box 1663, Los Alamos, NM 87545
Wesley. P. Unruh
Affiliation:
Los Alamos National Laboratory, P.O. Box 1663, Los Alamos, NM 87545
Ross. H. Plovnick
Affiliation:
3M Ceramic Technology Center, 201–4N-01 3M Center, St. Paul, MN 55144
Get access

Abstract

Continuous yttria-stabilized zirconia ceramic fibers approximately 10–15 μm in diameter have been rapidly sintered by pulling them through a tuned, 2.45 GHz single-mode TE103 microwave cavity in ambient air. The resulting fibers were analyzed by X-ray diffraction, scanning electron microscopy, and single-filament tensile tests. They were found to be unsplit, to have a submicron grain structure and a tetragonal crystal structure, and to exhibit considerable strength and flexibility.

Type
Research Article
Information
MRS Online Proceedings Library (OPL) , Volume 347: Symposium O – Microwave Processing of Materials IV , 1994 , 551
Copyright
Copyright © Materials Research Society 1994

Access options

Get access to the full version of this content by using one of the access options below. (Log in options will check for institutional or personal access. Content may require purchase if you do not have access.)

References

REFERENCES

1. Vogt, G. J. and Unruh, W. P., “Microwave Hybrid Heating of Alumina Filaments,” in Microwaves: Theory and Application in Materials Processing II. edited by Clark, D.E., Tinga, W.R., and Laia, J.R. Jr, (Ceram. Trans. 36, Westerville, OH, 1993) pp. 297–306.Google Scholar
2. Vogt, G. J. and Unruh, W. P., “Processing Aerosols and Filaments in a TM010 Microwave Cavity at 2.45 GHz,” in Microwave Processing of Materials HI. ed. by Beatty, R. L., Sutton, W. H., and Iskander, M. F. (Mater. Res. Soc. Proceedings 269, Materials Research Society, Pittsburgh, PA, 1992) pp. 245–250.Google Scholar
3. Sutton, W. H., “Microwave Processing of Ceramic Materials,” Am. Ceram. Soc. Bull., 68 (2) 376–86 (1989).Google Scholar
4. Sutton, W. H. in Microwave Processing of Materials III, op. cit., pp. 3–20.Google Scholar
5. Wilson, J. and Kunz, S. M., “Microwave Sintering of Partially Stabilized Zirconia,” J. Am. Ceram. Soc. 71 (1), C–40–C-41 (1988).Google Scholar
6. Tian, Y.-L., Li, B.-S., Shi, J.-L., Xu, Y.-P., Guo, J.-K., and Yen, D.-S., “Microwave Sintering of Y2O3 (3%)-ZrO2 (TZP),” in Microwaves: Theory and Application in Materials Processing. edited by Clark, D.E., Gac, F.D., and Sutton, W.H. (Ceram. Trans. 21, The American Ceramic Society, Westerville, OH, 1991) pp. 577–84.Google Scholar
7. Janney, M. A., Calhoun, C. L., and Kimrey, H. D., “Microwave Sintering of Solid Oxide Fuel Cell Materials: I, Zirconia-8mol% Yttria,” J. Am. Ceram. Soc. 75 (2), 341–46 (1992).Google Scholar
8. Funkenbusch, E. F. and Tran, T. T., “Zirconium Oxide Fibers and Process for Their Preparation,” U.S. Patent No. 4,937,212 (26 June 1990).Google Scholar
9. Christiansen, D. E. and Unruh, W. P., “Use of a TM010 Microwave Cavity at 2.45 GHz for Aerosol and Filament Drying,” ), in Microwaves: Theory and Application in Materials Processing, op. cit., pp. 597–604.Google Scholar