Hostname: page-component-7479d7b7d-t6hkb Total loading time: 0 Render date: 2024-07-10T13:25:05.576Z Has data issue: false hasContentIssue false
  • English
  • Français

Modeling Stress and Failure in Shrinking Coatings

Published online by Cambridge University Press:  21 March 2011

Herong Lei ,
Lorraine F. Francis ,
William W. Gerberich  and
L. E. Scriven
Herong Lei
Affiliation:
Department of Chemical Engineering & Materials ScienceUniversity of Minnesota, Minneapolis, MN 55455
Lorraine F. Francis
Affiliation:
Current address: Eastman Kodak Company, Kodak Park, Rochester, NY 14652
William W. Gerberich
Affiliation:
Current address: Eastman Kodak Company, Kodak Park, Rochester, NY 14652
L. E. Scriven
Affiliation:
Current address: Eastman Kodak Company, Kodak Park, Rochester, NY 14652
Get access

Abstract

Drying or curing of a coating after vitrification or gelation is accompanied by stress development. Evaporation of solvent, polymerization, cross-linking, and cooling all cause shrinkage, but adhesion of the coating to the substrate prevents shrinkage to a stress-free state. The interaction of shrinkage and restraint creates strain and stress. If the local stress grows above the local strength of the coating, it can produce cracking, delamination, or other defects.

A large deformation elastic model based on the Galerkin/finite element method is developed to analyze stress development in coatings subject to uniform shrinkage. The model is used to analyze effects of delamination and surface cracks. The strain energy release rates in both delamination and surface cracking are computed at different crack lengths. In both cases, results show that thicker coatings have larger energy release rates and are more vulnerable to cracking. A key conclusion of this modeling is that a crack can propagate only from an inherent flaw greater than a certain size. If the coating is thin enough so that the maximum energy release rate is less than the crack growth resistance, then no inherent flaws in the coating can grow into a crack, and so the coating remains crack-free. The model also shows how to calculate a critical coating thickness, i.e., the maximum thickness of a coating that can remain crack-free.

Type
Research Article
Information
MRS Online Proceedings Library (OPL) , Volume 653: Symposium Z – Multiscale Modeling of Materials-2000 , 2000 , Z10.5.1
Copyright
Copyright © Materials Research Society 2001

Access options

Get access to the full version of this content by using one of the access options below. (Log in options will check for institutional or personal access. Content may require purchase if you do not have access.)

References

1. Croll, S. G., J. Appl. Polym. Sci., 23, 847 (1979).Google Scholar
2. Colina, H., Arcangelis, L. de, and Roux, S., Phys. Rev. B, 48 3666–3676 (1993).Google Scholar
3. Garino, T. J., Mater. Res. Soc. Symp. Proc., 180, 497–502 (1990).Google Scholar
4. Chiu, R. C., Garino, T. J., and Cima, M. J., J. Am. Ceram. Soc., 76 2257–2264 (1993).Google Scholar
5. Lange, F. F., Science 273 903–909 (1996).Google Scholar
6. Payne, J. A., Stress evolution in solidifying coatings, P h.D. Thesis, University of Minnesota (1998).Google Scholar
7. Lee, E. H., J. Appl. Mech., 91 1 (1969).Google Scholar
8. Tam, S. Y., Scriven, L. E., and Stolarski, H. K., Mater. Res. Soc. Symp. Proc., 356, 547 (1995).10.1557/PROC-356-547Google Scholar
9. Malvern, L. E., Introduction to the mechanics of a continuous medium, Prentice-Hall Inc., New Jersey (1969).Google Scholar
10. Lei, H., Flow, deformation, stress and failure in solidifying coatings, Ph.D. Thesis, University of Minnesota (1999).Google Scholar
11. Treloar, L. R. G., Introduction to polymer science, Wykeham, London (1970).Google Scholar
12. Miyazaki, N. and Watanabe, T., Eng. Fract. M., 22 975–987 (1985).Google Scholar