Hostname: page-component-5c6d5d7d68-pkt8n Total loading time: 0 Render date: 2024-09-01T11:26:01.518Z Has data issue: false hasContentIssue false
  • English
  • Français

Nonthermal Microwave Plasma Synthesis of Crystalline Titanium Oxide & Titanium Nitride Nanoparticles

Published online by Cambridge University Press:  25 February 2011

Prabhjot Mehta ,
A. K. Singh  and
A. I. Kingon
Prabhjot Mehta
Affiliation:
Dept. Mat. Sci. & Eng., North Carolina State University, Raleigh, NC, 27695–7919
A. K. Singh
Affiliation:
On study leave from Phy. Dept. BHU, VARANASI–221005, INDIA
A. I. Kingon
Affiliation:
Dept. Mat. Sci. & Eng., North Carolina State University, Raleigh, NC, 27695–7919
Get access

Abstract

We report the nonthermal synthesis of ultrafine crystalline nanoparticles of titanium oxide and titanium nitride. The nanoparticles are formed by gas phase reactions between precursor gases dissociated in the microwave plasma. For the production of titanium nitride, titanium tetraisopropoxide (TTIP) and ammonia or nitrogen precursor gases are used. For titanium oxide production TTIP and oxygen are used as precursor gases. In both cases ultrahigh purity argon serves as a carrier gas and diluent.Transmission electron microscopy (TEM) revealed that the titanium nitride powders so formed were either cubic (TiN) or tetragonal (Ti2N) depending on the operational conditions, particularly the relative nitrogen gas flow rates. Ammonia gas was found to be a much more reactive nitrogen source than molecular nitrogen gas. For the titanium oxide growth an excess of oxygen was utilized to achieve TiO2. Powders collected from the gas phase corresponded to the rutile (tetragonal) phase. However, powders collected from the cavity walls corresponded to the high temperature and pressure (orthorhombic) 13-TiO2. There was also evidence of a polytypically modulated phase of TiO2, with the observed c-periodicity double the parent c-periodicity of the rutile phase. Using a low oxygen flow rate during powder formation led to the formation of orthorhombic Ti3O5 “powders”. The powders were easily sinterable by in situ electron beam annealing in the electron microscope, with an estimated temperature of around 550°C. This is much lower than the temperatures normally required to sinter these materials.

Type
Research Article
Information
MRS Online Proceedings Library (OPL) , Volume 249: Symposium Q – Synthesis and Processing of Ceramics: Scientific Issues , 1991 , 153
Copyright
Copyright © Materials Research Society 1992

Access options

Get access to the full version of this content by using one of the access options below. (Log in options will check for institutional or personal access. Content may require purchase if you do not have access.)

References

REFERENCES

1. Janeway, P. A., Adv. Cer. 28 28 (1990).Google Scholar
2. Harbuck, D. D., Davidson, C. F. and Shirts, M. B., J. Metals 38, 47 (1986).Google Scholar
3. Saeki, Y., Matsuzaki, R., Yazima, A. and Akiyama, M., Bull. Chem. Soc. Jpn. 55 (10), 3193 (1982).Google Scholar
4. Singh, A. K. and Kingon, A. I. in Cluster and Cluster assembled Materials. edited by Averback, R. S., Nelson, D. L., and Bernholc, J. J Mat. Res. Soc. Symp. Proc. 206, Boston, MA 1990) pp551–556.Google Scholar
5. Singh, A. K., Mehta, P. and Kingon, A. I., Ceramic Trans. 21, 421 (1991).Google Scholar
6. lanno, N. J., Ahmed, A. V., and Englebirt, D. E., J. Electrochem. Soc. 136 (1), 276 (1989).Google Scholar
7. Ogihara, T., Ikeda, M., Kato, M., and Mizutani, N., J. Am. Ceram. Soc., 72 [9], 1598 (1989).CrossRefGoogle Scholar
8. Kirbir, F. and Komiyama, H., The Canadian Journal of Chemical Engineering, 65, 759 (1987).Google Scholar
9. Fukishima, K., Yamada, I. and Takagi, T., J. Appl. Phys. 58 (11),4146 (1985).CrossRefGoogle Scholar