Hostname: page-component-5c6d5d7d68-wpx84 Total loading time: 0 Render date: 2024-08-22T08:41:55.077Z Has data issue: false hasContentIssue false
  • English
  • Français

Property Comparison of Melt-Spun Ribbons and Consolidated Powders of Ni3A1-B

Published online by Cambridge University Press:  21 February 2011

K-M Chang ,
A. I. Taub  and
S. C. Huang
K-M Chang
Affiliation:
Metallurgy Laboratory, General Electric Company, Corporate Research and Development Center, P.O. Box 8, Schenectady, New York 12345 U.S.A.
A. I. Taub
Affiliation:
Metallurgy Laboratory, General Electric Company, Corporate Research and Development Center, P.O. Box 8, Schenectady, New York 12345 U.S.A.
S. C. Huang
Affiliation:
Metallurgy Laboratory, General Electric Company, Corporate Research and Development Center, P.O. Box 8, Schenectady, New York 12345 U.S.A.
Get access

Abstract

Ductile intermetallic Ni3 Al-B alloys have been processed through three rapid solidification techniques: melt spinning, gas atomization, and plasma deposition. Different thermal treatment was required for each rapidly solidified product to form samples for mechanical evaluation. Melt-spun ribbons were tested in ribbon form in the as-cast or annealed conditions, while atomized powders were tested after consolidation by hot isostatic pressing (HIP) or low pressure plasma deposition. Alloy strength, as well as tensile ductility, was found to depend strongly on processing technique, thermal treatment, sample geometry, and most importantly, alloy chemistry. Microstructural and fractographic observations indicate that grain boundary brittleness caused by material processing history plays the major role in determining the alloy's mechanical behavior.

Type
Research Article
Information
MRS Online Proceedings Library (OPL) , Volume 39: Symposium G – High-Temperature Ordered Intermetallic Alloys I , 1984 , 335
Copyright
Copyright © Materials Research Society 1985

Access options

Get access to the full version of this content by using one of the access options below. (Log in options will check for institutional or personal access. Content may require purchase if you do not have access.)

References

REFERENCES

1. Guard, J.W. and Westbrook, J.H.: Trans. TMS-AIME, 1959, vol.215, p. 807.Google Scholar
2. Pope, D.P. and Ezz, S.S.: Inter. Metals Rev., 1984, vol.23, p. 136.Google Scholar
3. Aoki, K. and Izumi, O.: J. Japan Metal. Soc., 1979, vol.43, p. 358.Google Scholar
4. Klarstrom, D.L.: “Ni3 Al VIM ESR Ingots,” presented at ECUT Workshop on “Production and Fabrication of Ordered Intermetallic Alloys,” Oak Ridge National Lab., TN, Sept. 25–26, 1984.Google Scholar
5. Taub, A.I., Huang, S.C., and Chang, K.M.: “Stoichiometry Effects on the Strengthening and ductilization of Ni3 Al by Boron Modification and Rapid Solidification,” in Proc. 39th Symposium of Mechanical Failures Prevention Group, Gaitherburg, MD, May 1–3, 1984.Google Scholar
6. Liu, C.T., et. al.: “Development of Ordered Intermetallic Alloys for High Temperature Use,” presented at ECUT Workshop on “Production and Fabrication of Ordered Intermetallic Alloys,” Oak Ridge National Lab., TN, Sept. 25–26, 1984.Google Scholar
7. Taub, A.I., Huang, S.C., and Chang, K.M.: Met. Trans. A, 1984, vol.15A, p. 399.Google Scholar
8. Huang, S.C. and Laforce, R.P.: Mat. Res. Soc. Symp. Proc., Nov. 1983, Boston, MA, vol 28, “Rapidly Solidified Metastable Materials”, ed. Kear, B.H. and Giessen, B.C., p. 125.Google Scholar
9. Jackson, M.R., Rairden, I.R., 3.Smith, S., and Smith, R.W.: J. Metals., 1981, vol.33, no. 11, p. 23.Google Scholar
10. Chang, K.M., Huang, S.C., and Taub, A.I.: Mat. Res. Soc. Symp. Proc., Nov. 1983, Boston, MA, vol.28, “Rapidly Solidified Metastable Materials ed. Kear, B.H. and Giessen, B.C.., p. 401.Google Scholar
11. Huang, S.C., Taub, A.I., and Chang, K.M.: Acta Met., 1984, vol.32, p. 1703 Google Scholar