Hostname: page-component-5c6d5d7d68-qks25 Total loading time: 0 Render date: 2024-08-26T11:22:24.104Z Has data issue: false hasContentIssue false
  • English
  • Français

Quantitative Three-Dimensional Characterization of the Morphology of Stressed and Electromigrated Aluminum Lines

Published online by Cambridge University Press:  15 February 2011

George O. Ramseyer ,
Joseph V. Beasock ,
Herbert F. Helbig  and
Lois H. Walsh
George O. Ramseyer
Affiliation:
Rome Laboratory/ERDR, 525 Brooks Rd., Griffiss AFB, NY 13441-4505
Joseph V. Beasock
Affiliation:
Rome Laboratory/ERDR, 525 Brooks Rd., Griffiss AFB, NY 13441-4505
Herbert F. Helbig
Affiliation:
Rome Laboratory/ERDR, 525 Brooks Rd., Griffiss AFB, NY 13441-4505
Lois H. Walsh
Affiliation:
Rome Laboratory/ERDR, 525 Brooks Rd., Griffiss AFB, NY 13441-4505
Get access

Abstract

The volumes of slit, edge, erosion and erosion/slit voids in stressed and electromigrated aluminum conductor lines were quantitatively determined with low resolution standard and high resolution enhanced tips by atomic force microscopy. These three-dimensional results were compared to semiquantitative determinations of void volumes extrapolated from two-dimensional backscattered scanning electron microscopy area determinations of the passivated aluminum conductor. After the passivation was removed by plasma etching, void volumes were also determined from two-dimensional scanning electron microscopy micrographs. The volumes of the nearest hillocks on the anodic side of the voids were quantitatively determined by atomic force microscopy, and these hillock volumes were determined to be independent of the respective void volumes.

Type
Research Article
Information
MRS Online Proceedings Library (OPL) , Volume 391: Symposium T – Materials Reliability in Microelectronics V , 1995 , 373
Copyright
Copyright © Materials Research Society 1995

Access options

Get access to the full version of this content by using one of the access options below. (Log in options will check for institutional or personal access. Content may require purchase if you do not have access.)

References

1 Black, J.R., Proc. 6th IEEE Symp. Reliability in Phys., 148 (1967).Google Scholar
2 Curry, J., Fitzgibbon, G., Guan, Y., Muollo, R., Nelson, G. and Thomas, A., Proc. 22nd IEEE Reliability Phys. Symp., 6 (1984).Google Scholar
3 Mattila, J.B., Levi, M.W. and Walsh, L.H., Proc. 9th International VLSI Multilevel Interconnect Conf, 430 (1992).Google Scholar
4 Kime, Y.J. and Grach, P., in Materials Reliability in Microelectronics IV, edited by Borgesen, P., Coburn, J.C., Sanchez, J.E. Jr., Rodbell, K.P. and Filter, W.F.(Mater. Res. Soc. Proc. 338, Pittsburgh, PA, 1994) pp. 255–260.Google Scholar
5 Ramseyer, G.O., Beasock, J.V., Sylla, W.K. and Walsh, L.H., in Interface Control of Electrical, Chemical, and Mechanical Properties, edited by Murarka, S.P., Rose, K., Ohmi, T. and Seidel, T. (Mater. Res. Soc. Proc. 318, Pittsburgh, PA, 1994) pp. 329–334.Google Scholar
6 Ramseyer, G.O., Beasock, J.V., Renz, T.E. and Walsh, L.H., in Materials Reliability in Microelectronics IV, edited by Borgesen, P., Coburn, J.C., Sanchez, J.E. Jr., Rodbell, K.P. and Filter, W.F.(Mater. Res. Soc. Proc. 338, Pittsburgh, PA, 1994) pp. 421–426.Google Scholar
7 Augur, R.A., Proc. 32nd IEEE Symp. Reliability Phys., 266 (1994).Google Scholar
8 LaCombe, D.J. and Parks, E.L., Proc. 24th IEEE Reliability Phys. Symp., 1 (1986).Google Scholar