Hostname: page-component-7479d7b7d-jwnkl Total loading time: 0 Render date: 2024-07-12T08:36:56.487Z Has data issue: false hasContentIssue false
  • English
  • Français

Rapid Thermal Processor Modeling, Control, and Design for Temperature Uniformity

Published online by Cambridge University Press:  21 February 2011

Terrence J. Riley  and
Ronald S. Gyurcsik
Terrence J. Riley
Affiliation:
Department of Electrical and Computer Engineering, North Carolina State University, Raleigh, NC
Ronald S. Gyurcsik
Affiliation:
Department of Electrical and Computer Engineering, North Carolina State University, Raleigh, NC
Get access

Abstract

With the ability to perform heat cycles on a wafer quickly and within low thermal budgets, Rapid Thermal Processor (RTP) systems offer potential advantages over conventional furnaces. However, RTP' have an inherent problem with wafer temperature uniformity which can cause process nonuniformity and wafer stress.

In this work, a thermodynamic model of a wafer is used to form an understanding of the wafer heating problem. This model shows that an idealized heating flux density profile can maintain thermal uniformity at steady-state temperatures. This profile uniformly heats the wafer while counteracting the additional cooling at the wafer edge. However, this profile induces temperature nonuniformities during wafer temperature transients, such as overheating of the edge during temperature rises. Therefore, a dynamic flux-density profile is needed during temperature transients to ensure continuous temperature uniformity. The model is used to predict the steady-state and dynamic profiles required to process a wafer with complete temperature uniformity. The predicted profiles can be used to adapt an RTP chamber and control system to approach production of uniform wafers and also for the design of new systems. This paper will explain the theory of wafer heating, describe the dynamic profiles required for continuous uniformity, review the wafer model, show the result of an idealized profile for steady state and transients processing, and present a new control methodology to achieve uniform temperatures.

Type
Research Article
Information
MRS Online Proceedings Library (OPL) , Volume 303: Symposium G – Rapid Thermal and Integrated Processing II , 1993 , 223
Copyright
Copyright © Materials Research Society 1993

Access options

Get access to the full version of this content by using one of the access options below. (Log in options will check for institutional or personal access. Content may require purchase if you do not have access.)

References

REFERENCES

1. Roozeboom, F. and Parekh, N., J. Vac. Sci. Tech. B 8, 1249 (1990).Google Scholar
2. Lord, H. A., IEEE Transactions on Semiconductor Manufacturing 1, 105 (1988).Google Scholar
3. Kakoschke, R. and Bussmann, E., in Rapid Thermal Annealing/Chemical Vapor Deposition and Integrated Processing, edited by Hodul, D., (Mater. Res. Soc. Proc. 146, Pittsburgh, PA, 1989), pages 473–82.Google Scholar
4. Kakoschke, R., Bussmann, E., and Föll, H., AppL Phys. A 50, 141 (1990).Google Scholar
5. Kakoschke, R., Bussmann, E., and Föll, H., Appl. Phys. A 52, 52 (1991).Google Scholar
6. Moslehi, M. M., IEEE Transactions on Semiconductor Manufacturing 2, 130 (1989).Google Scholar
7. Gyurcsik, R. S., Riley, T. J., and Sorrell, F. Y., IEEE Transactions on Semiconductor Manufacturing 4, 9 (1991).Google Scholar
8. Sorrell, F. Y., Fordham, M. J., Ozturk, M. C., and Wortman, J. J., IEEE Transactions on Electron Devices 39, 75 (1992).Google Scholar
9. Akiyama, N., Inoue, Y., and Suzuki, T., Japan. J. Appl. Phys. 25, 1619 (1986).Google Scholar
10. Semiconductor Equipment and Materials International, 1989 Standards: Materials.Google Scholar