Hostname: page-component-77c89778f8-9q27g Total loading time: 0 Render date: 2024-07-18T07:32:31.642Z Has data issue: false hasContentIssue false
  • English
  • Français

Single Shot of Arf Laser-Induced Photochemical Nucleation of Copper on Polyethylene-Terephthalate Surface

Published online by Cambridge University Press:  11 February 2011

H. Tokunaga  and
M. Murahara
H. Tokunaga
Affiliation:
Department of Electrical Engineering, Tokai University, 1117 Kitakaname, Hiratsuka-shi, Kanagawa 259–1292, Japan
M. Murahara
Affiliation:
Department of Electrical Engineering, Tokai University, 1117 Kitakaname, Hiratsuka-shi, Kanagawa 259–1292, Japan
Get access

Abstract

Copper nuclei was grown on a PET surface in the copper sulfate water solution ambience with only one shot of ArF laser.· General electronic circuit printed boards have been made by sticking the copper foils with adhesive agents after having made the foil surface rough. Consequently, even the printed board of low conductivity might generate a high frequency noise due to the difference between the copper foils and adhesive agents. If atoms composing plastics and metal could be combined by a chemical method instead of the conventional physical methods, a hybrid material made of both plastics and metal would be produced.

We have reported for the substitution of copper atoms on an all-aromatic-polyimide surface by a single shot of ArF laser irradiation In this study, with one single shot of ArF laser, we succeeded in growing the Cu nuclei on the PET film whose ultraviolet absorption is lower than all-aromatic-polyimide. The sample surface was photo-oxidized with the Xe2 excimer lamp in pre-treatment. A fused silica glass was placed on the sample surface, and the sulfate water solution was poured into the gap between the glass and the sample to form a thin liquid layer. Then, the sample was vertically irradiated once by the circuit patterned ArF laser light with the laser fluence of 28mJ/cm2. The photo-dissociated copper atom formed the C-O-Cu bond with active oxygen to sub stitute on the PET surface. The modified sample was, then, immersed in the electro less plating solution at 60 degrees Celsius for 15 minutes; the copper thin film of about 24mm was grown on the modified surface.

Type
Research Article
Information
MRS Online Proceedings Library (OPL) , Volume 734: Symposia A/B – Defect-Mediated Phenomena in Ordered Polymers – Polymer/Metal Interfaces and Defect Mediated Phenomena in Ordered Polymers , 2002 , A5.3
Copyright
Copyright © Materials Research Society 2003

Access options

Get access to the full version of this content by using one of the access options below. (Log in options will check for institutional or personal access. Content may require purchase if you do not have access.)

References

REFERENCES

1. Tsury, Y, Mchinaga, K, Kume, M and Ooyagi, Y: Faculty of Eng: Fukuoka Technical paper. 53, No7, 2002·Google Scholar
2. Komagine, R, Ohaku, T, Sato, R, Tate, H, Takaba, S: electric wire of Hitachi U.D.C.621.3.049.7: 621.793.3:678.7.057.74, No20, 2001–2001 Google Scholar
3. Hidaka, K: Kanto Kasei Co., Ltd. Technical paper. 53, No7, 2002 Google Scholar
4. Tokunaga, H., Ogawa, Y. and Murahara, M.; Mat, Res. Soc. Symp. Proc. 700(2001) pp. 185–191.CrossRefGoogle Scholar
5. Okoshi, M, Murahara, M and Toyoda, K.: M.R.S. Symp. Proc. 158, 33, 1990.CrossRefGoogle Scholar
6. Okoshi, M, Murahara, M and Toyoda, K.: M.R.S. Symp. Proc. 201, 451, 1991.CrossRefGoogle Scholar
7. Ikegame, T. and Murahara, M.: M.R.S. Symp. Proc. 98, 23, 1998.Google Scholar
8. Sito, , and Murahara, M: M.R.S. Symp. Proc. 98, 23, 1998.Google Scholar
9. Murahara, M: M.R.S. Symp. Proc. 98, 23, 1998.Google Scholar
10. Murahara, M: JP. Patent No 3316069 (7 June 2002).Google Scholar