Hostname: page-component-7479d7b7d-fwgfc Total loading time: 0 Render date: 2024-07-10T00:06:25.208Z Has data issue: false hasContentIssue false
  • English
  • Français

Tem Specimen Preparation of Tial Alloy Powders Produced by Plasma Rotating Electrode Process

Published online by Cambridge University Press:  21 February 2011

M. Nishida ,
A. Chiba ,
T. Tateyama ,
R. Tomoshige ,
K. Morita  and
E. Aoyagi
M. Nishida
Affiliation:
Department of Materials Science and Resource Engineering, Kumamoto University, 2-39-1 Kurokami Kumamoto 860 Japan
A. Chiba
Affiliation:
Department of Materials Science and Resource Engineering, Kumamoto University, 2-39-1 Kurokami Kumamoto 860 Japan
T. Tateyama
Affiliation:
Department of Materials Science and Resource Engineering, Kumamoto University, 2-39-1 Kurokami Kumamoto 860 Japan
R. Tomoshige
Affiliation:
Department of Materials Science and Resource Engineering, Kumamoto University, 2-39-1 Kurokami Kumamoto 860 Japan
K. Morita
Affiliation:
Department of Materials Science and Resource Engineering, Kumamoto University, 2-39-1 Kurokami Kumamoto 860 Japan
E. Aoyagi
Affiliation:
Institute for Materials Research, Tohoku University, 2-1-1 Katahira, Aoba-ku, Sendai 980, Japan
Get access

Abstract

TEM specimens of PREPed Ti -48 at.% Al powders can be prepared reproducibly in a straight-forward manner. There are two kinds of powders with respect to surface and crosssectional morphologies. One is with an Widmanstitten-like structure and or a surface relief of martensitic phase and the other is with a dendritic structure. The primary phase during solidification and relative cooling rate in both the powders are discussed by comparing the macroscopic and microscopic features.

Type
Research Article
Information
MRS Online Proceedings Library (OPL) , Volume 254: Symposium W – Specimen Preparation for Transmission Electron Microscopy of Materials III , 1991 , 185
Copyright
Copyright © Materials Research Society 1992

Access options

Get access to the full version of this content by using one of the access options below. (Log in options will check for institutional or personal access. Content may require purchase if you do not have access.)

References

1. Graves, J.A., Perepezko, J.H., Ward, C.H. and Froes, F.H., Scripta METALL 21,567(1987).CrossRefGoogle Scholar
2. Graves, J.A., Bendersky, L.A., Biancaniello, F.S., Perepezko, J.H. and Boettinger, W.J., Mat. Sci. and Eng. 98 265(1988).Google Scholar
3. EAdkins, N.J. and Ricks, R.A., in Proc. Int, Conf. on Powder Metallurgy. edited by Kaysser, W.A. and Huppermann, W.J. (Verlag Schmidt, Freiburg, 1986),p.969.Google Scholar
4. Boettinger, W.J., Bendersky, L. and Early, J.G., METALL. TRANS. A. 17A,781(1986).CrossRefGoogle Scholar
5. McCullough, C., Valencia, J.J., Levi, C.G. and Mehrabian, R., Acta metall. 37,1337(1989).Google Scholar
6. Loiseau, P.A. and Lasalmonie, A., Acta Cryst. B39,580(1983).Google Scholar
7. JJ.Valencia, McCullough, C., Levi, C.G. and Mehrabian, R., Acta metall. 37,2517(1989).CrossRefGoogle Scholar