Hostname: page-component-7bb8b95d7b-5mhkq Total loading time: 0 Render date: 2024-10-06T08:21:19.647Z Has data issue: false hasContentIssue false
  • English
  • Français

Thermal and Mechanical Analysis of a Multichip Module

Published online by Cambridge University Press:  15 February 2011

M. S. Hu
M. S. Hu*
Affiliation:
Diceon Electronics Inc., Advanced Development Center, Chatsworth, CA 91311
Get access

Abstract

High speed, high density packaging requirements have made multichip modules (MCM) one of the most active areas of research in the electronic industry.

High density printed wiring board (PWB) have low production cost and good electrical performance. However, the most questioned issue in application is the reliability. As a result, a thermal and mechanical analysis on a MCM has been conducted to understand its feasibility. The results indicate that with proper design, the components can operate under satisfactory conditions on PWB laminates.

Type
Research Article
Information
MRS Online Proceedings Library (OPL) , Volume 264: Symposium G – Electronic Packaging Materials Science VI , 1992 , 219
Copyright
Copyright © Materials Research Society 1992

Access options

Get access to the full version of this content by using one of the access options below. (Log in options will check for institutional or personal access. Content may require purchase if you do not have access.)

References

1. O'brien, K., Williams, T., Hybrid Circuits Tech., 8 (12),14 (1991); K. O'brien, T. Williams, Hybrid Circuits Tech., 9 (1), 6 (1992).Google Scholar
2. Ginsberg, G.L., Sandborn, P., Bauer, C.E., Gustafsson, K., Schaper, L., Caswell, G., Segelken, J.M., INSIDE ISHM, 19 (2), 5 (1992).Google Scholar
3. Kato, M., ICMCM Proc. ‘92, April 1–3, 485 (1992).Google Scholar
4. Tuck, J., Circuit Assembly, 3 (3), 24 (1992).Google Scholar
5. Murray, J., P.C. Fab., 15 (2), 44 (1992).Google Scholar
6. Rubin, L.S., Jayaraj, K., Burnett, J.M., IEPS Conference Proc., Sept. 15–18, 72 (1991).Google Scholar
7. Mumby, S.J., J. Elec. Mater., 18 (2), 241 (1989).Google Scholar
8. Snyder, W.W., P.C. Fab., 13 (3), (1990).Google Scholar
9. Mansuria, M.S., IEPS Conference Proc., Sept. 15–18, 111 (1991).Google Scholar
10. Simons, R.E., Solid State Tech., 26 (10), 131 (1983).Google Scholar
11. Markstein, H.W., Elec. Pack. Product., 31 (7), 50 (1991).Google Scholar
12. Isaac, J., Martinez, M., ICMCM Proc. ‘92, April 1–3, 41 (1992).Google Scholar
13. Suhir, E., J. App. Mech., 53 (3), 657 (1986).CrossRefGoogle Scholar
14. Glaser, J.C., J. Elec. Pack., 112, 24 (1990).Google Scholar
15. Nakano, F., Soga, T., Amagi, S., ISHM ‘87 Proc., 536 (1987).Google Scholar
16. Suhir, E., Segelken, J.M., J. Elec. Pack., 112, 327 (1990).CrossRefGoogle Scholar
17. Jackson, R.L., Carnevali, P., Frazier, J.D., ISHM ‘91 Proc., 82 (1991).Google Scholar
18. Otsuki, H., Morishita, H., Kokogawa, T., Adachi, K., Matsukawa, F., Takasago, H., ISHM ‘91 Proc., 86 (1991).Google Scholar
19. Yamaguchi, Y., Kato, M., Proc. Nepcon West ‘91, (1991).Google Scholar
20. Honore, J.P., Rubin, H.D., Zierold, M.K., Proc. Nepcon West ‘92, 1372 (1992).Google Scholar