Hostname: page-component-5c6d5d7d68-wpx84 Total loading time: 0 Render date: 2024-08-07T12:21:50.990Z Has data issue: false hasContentIssue false
  • English
  • Français

Magnetic Properties of Mechanically Alloyed Nano-Crystalline Cu/Fe Composites

Published online by Cambridge University Press:  15 February 2011

C. P. Reed ,
S. C. Axtell ,
R. J. De Angelis ,
B. W. Robertson ,
V. V. Munteanu  and
S. H. Liou
C. P. Reed
Affiliation:
Center for Materials Research and Analysis and Dept. of Mechanical Engineering, University of Nebraska-Lincoin, Lincoln, Nebraska 68588-0656
S. C. Axtell
Affiliation:
Center for Materials Research and Analysis and Dept. of Mechanical Engineering, University of Nebraska-Lincoin, Lincoln, Nebraska 68588-0656
R. J. De Angelis
Affiliation:
Center for Materials Research and Analysis and Dept. of Mechanical Engineering, University of Nebraska-Lincoin, Lincoln, Nebraska 68588-0656
B. W. Robertson
Affiliation:
Center for Materials Research and Analysis and Dept. of Mechanical Engineering, University of Nebraska-Lincoin, Lincoln, Nebraska 68588-0656
V. V. Munteanu
Affiliation:
Center for Materials Research and Analysis and Dept. of Mechanical Engineering, University of Nebraska-Lincoin, Lincoln, Nebraska 68588-0656
S. H. Liou
Affiliation:
Dept. of Physics and Astronomy, University of Nebraska-Lincoin, Lincoin, Nebraska 68588-0656
Get access

Abstract

Metal powders of the composition 70 at% Cu and 30 at% Fe were produced by high energy mechanical alloying of the elemental powders. The powders were processed in a Spex 8000 mixer/mill for various times to investigate the potential of the mechanical alloying process for producing nano-composite structures with modified magnetic properties. Optical microscopy revealed a layered structure of alternating copper and iron that developed upon milling. The spacing between the layers decreased with milling time, becoming optically unresolvable (< 1 μm) after four hours of milling. A single profile x-ray diffraction profile shape analysis technique was used to determine the average diffracting particle size of the copper and iron phases. The diffracting particle size decreases with alloying time reaching values of 7.5 nm and 2 nm, for copper and iron respectively, after eight hours of alloying. The magnetic coercivity increased with milling time initially, reaching a maximum value above 300 Oe after six hours of milling. These results are discussed and compared to results obtained in Ag/Fe and Cu/Fe nano-composite films.

Type
Research Article
Information
MRS Online Proceedings Library (OPL) , Volume 274: Symposium R – Submicron Multiphase Materials , 1992 , 177
Copyright
Copyright © Materials Research Society 1992

Access options

Get access to the full version of this content by using one of the access options below. (Log in options will check for institutional or personal access. Content may require purchase if you do not have access.)

References

REFERENCES

1. Warren, B.E., X-Ray Diffraction, Addison-Wesley, New York, 1969.Google Scholar
2. Kuo, H.K., Ganesan, P. and De Angelis, R.J., A Method to Study Sintering of a Suoported Metal Catalyst, Microstructural Science, vol. 8, Elsevier North Holland, 1980.Google Scholar
3. Benjamin, J.S. and Volin, T.E., The Mechanism of Mechanical Alloying, Metall. Trans., vol.5, 1974, p. 1929.Google Scholar
4. Luborsky, F.E., High Coercive Materials Development of Elongated Particle Magnets, J. Appl. Phys., vol 32, no. 3, 1961, p. 171S.Google Scholar
5. Reed, C.P., De Angelis, R.J., Zhang, Y.X. and Liou, S.H., Substructure-Magnetic Property Correlation in Fe/Ag Composite Thin Films, Advances in X-Ray Analysis, Vol. 34, Plenum Press, 1991, p. 557.Google Scholar
6. Zhang, Y.X., Liou, S.H., Angelis, R.J. De, Lee, K.W., Reed, C.P. and Nazareth, A., The Process Controlled Magnetic Properties in Nanostructured Fe/Aa Composite Films, J. Appl. Phys., vol.69 (8), 1991, p. 5273.Google Scholar
7. Childress, J.R., Chien, C.L. and Nathan, M., Granular Iron in a Metallic Matrix, Appl. Phys. Lett., vol.56 (1), 1990, p. 95.Google Scholar