Focus on Fluids
Nozzles, turbulence, and jet noise prediction
- Jonathan B. Freund
-
- Published online by Cambridge University Press:
- 29 November 2018, pp. 1-4
-
- Article
-
- You have access Access
- HTML
- Export citation
-
Jet noise prediction is notoriously challenging because only subtle features of the flow turbulence radiate sound. The article by Brès et al. (J. Fluid Mech., vol. 851, 2018, pp. 83–124) shows that a well-constructed modelling procedure for the nozzle turbulence can provide unprecedented sub-dB prediction accuracy with modest-scale large-eddy simulations, as confirmed by detailed comparison with turbulence and sound-field measurements. This both illuminates the essential mechanisms of the flow and facilitates prediction for engineering design.
JFM Papers
Temporal stability analysis of jets of lobed geometry
- Benshuai Lyu, Ann P. Dowling
-
- Published online by Cambridge University Press:
- 05 December 2018, pp. 5-39
-
- Article
- Export citation
-
A two-dimensional temporal incompressible stability analysis is performed for lobed jets. The jet base flow is assumed to be parallel and of a vortex-sheet type. The eigenfunctions of this simplified stability problem are expanded using the eigenfunctions of a round jet. The original problem is then formulated as an innovative matrix eigenvalue problem, which can be solved in a very robust and efficient manner. The results show that the lobed geometry changes both the convection velocity and temporal growth rate of the instability waves. However, different modes are affected differently. In particular, mode 0 is not sensitive to the geometry changes, whereas modes of higher orders can be changed significantly. The changes become more pronounced as the number of lobes
$N$ and the penetration ratio
$\unicode[STIX]{x1D716}$ increase. Moreover, the lobed geometry can cause a previously degenerate eigenvalue (
$\unicode[STIX]{x1D706}_{n}=\unicode[STIX]{x1D706}_{-n}$) to become non-degenerate (
$\unicode[STIX]{x1D706}_{n}\neq \unicode[STIX]{x1D706}_{-n}$) and lead to opposite changes to the stability characteristics of the corresponding symmetric (
$n$) and antisymmetric (
$-n$) modes. It is also shown that each eigenmode changes its shape in response to the lobes of the vortex sheet, and the degeneracy of an eigenvalue occurs when the vortex sheet has more symmetric planes than the corresponding mode shape (including both symmetric and antisymmetric planes). The new approach developed in this paper can be used to study the stability characteristics of jets of other arbitrary geometries in a robust and efficient manner.
Optimal disturbances and large-scale energetic motions in turbulent boundary layers
- Timothy B. Davis, Ali Uzun, Farrukh S. Alvi
-
- Published online by Cambridge University Press:
- 29 November 2018, pp. 40-80
-
- Article
- Export citation
-
We examine disturbances leading to optimal energy growth in a spatially developing, zero-pressure-gradient turbulent boundary layer. The slow development of the turbulent mean flow in the streamwise direction is modelled through a parabolized formulation to enable a spatial marching procedure. In the present framework, conventional spatial optimal disturbances arise naturally as the homogeneous solution to the linearized equations subject to a turbulent forcing at particular wavenumber combinations. A wave-like decomposition for the disturbance is considered to incorporate both conventional stationary modes as well as propagating modes formed by non-zero frequency/streamwise wavenumber and representative of convective structures naturally observed in wall turbulence. The optimal streamwise wavenumber, which varies with the spatial development of the turbulent mean flow, is computed locally via an auxiliary optimization constraint. The present approach can then be considered, in part, as an extension of the resolvent-based analyses for slowly developing flows. Optimization results reveal highly amplified disturbances for both stationary and propagating modes. Stationary modes identify peak amplification of structures residing near the centre of the logarithmic layer of the turbulent mean flow. Inner-scaled disturbances reminiscent of near wall streaks, and amplified over short streamwise distances, are identified in the computed streamwise energy spectra. In all cases, however, propagating modes surpass their stationary counterpart in both energy amplification and relative contribution to total fluctuation energy. We identify two classes of large-scale energetic modes associated with the logarithmic and wake layers of the turbulent mean flow. The outer-scaled wake modes agree well with the large-scale motions that populate the wake layer. For high Reynolds numbers, the log modes increasingly dominate the energy spectra with the predicted streamwise and wall-normal scales in agreement with superstructures observed in turbulent boundary layers.
A novel non-reflecting boundary condition for fluid dynamics solved by smoothed particle hydrodynamics
- Pingping Wang, A-Man Zhang, Furen Ming, Pengnan Sun, Han Cheng
-
- Published online by Cambridge University Press:
- 03 December 2018, pp. 81-114
-
- Article
- Export citation
-
Non-reflecting boundary conditions (NRBCs) play an important role in computational fluid dynamics (CFD). A novel NRBC based on the method of characteristics using timeline interpolations is proposed for fluid dynamics solved by smoothed particle hydrodynamics (SPH). It is performed by four layers of particles whose pressures and velocities are obtained through the Lagrange interpolation in the time domain which is derived from the propagation of characteristic waves between particles. The proposed NRBC can allow outward travelling pressure and velocity messages to pass through the boundary without obvious reflection. That is, with the implementation of the NRBC, the solution in a finite computational domain of interest is close to that in an infinite domain. Several numerical tests show that this NRBC is robust and applicable for a broad variety of hydrodynamics ranging from low to high speed.
Deformation of a biconcave-discoid capsule in extensional flow and electric field
- Sudip Das, Shivraj D. Deshmukh, Rochish M. Thaokar
-
- Published online by Cambridge University Press:
- 03 December 2018, pp. 115-144
-
- Article
- Export citation
-
Natural (red blood cells) and artificial biconcave-discoid-shaped capsules have immense biological (a cellular component of blood) and technological (as drug carrier) relevance, respectively. Their low reduced volume allows significant shape changes under external fields such as extensional flows (encountered at junctions and size-varying capillaries in biological flows) and electric fields (in applications such as electroporation and dielectrophoresis). This work demonstrates biconcave-discoid to capped-cylindrical and prolate-spheroid shape transitions of a capsule in uniaxial extensional flow as well as in DC and AC electric fields. The shape changes of a stress-free biconcave-discoid capsule in external fields are important in determining the momentum and mass transfer between the capsule and the medium fluid as well as dielectrophoresis and electroporation phenomena of a capsule in an electric field. The biconcave-discoid to capped-cylindrical/prolate-spheroid shape transition is demonstrated for both a capsule (with parameters relevant to drug delivery) as well as for a red blood cell (physiological conditions). However, significant differences are observed in this shape transition depending upon the applied external fields. In an extensional flow, the pressure-driven transition shows the equator being squeezed in and the poles being pulled out to deform into a capped cylinder at low capillary number and a prolate spheroid at high capillary number. On the other hand, in the transition driven by electric fields, the shoulders of the capsule seem to play a significant role in the dynamics. The shape transition in the electric fields depends upon the relative magnitude of the electric and the hydrodynamic response times, particularly relevant for the dynamics of red blood cells in physiological conditions. A new method of analysing the shape transition of red blood cells in AC electric fields is suggested, where a large separation of time scales is observed between the hydrodynamic and electric responses.
Instability of sheared density interfaces
- T. S. Eaves, N. J. Balmforth
-
- Published online by Cambridge University Press:
- 03 December 2018, pp. 145-171
-
- Article
- Export citation
-
Of the canonical flow instabilities (Kelvin–Helmholtz, Holmboe-wave and Taylor–Caulfield) of stratified shear flow, the Taylor–Caulfield instability (TCI) has received relatively little attention, and forms the focus of the current study. First, a diagnostic of the linear instability dynamics is developed that exploits the net pseudomomentum to distinguish TCI from the other two instabilities for any given flow profile. Second, the nonlinear dynamics of TCI is studied across its range of unstable horizontal wavenumbers and bulk Richardson numbers using numerical simulation. At small bulk Richardson numbers, a cascade of billow structures of sequentially smaller size may form. For large bulk Richardson numbers, the primary nonlinear travelling waves formed by the linear instability break down via a small-scale, Kelvin–Helmholtz-like roll-up mechanism with an associated large amount of mixing. In all cases, secondary parasitic nonlinear Holmboe waves appear at late times for high Prandtl number. Third, a nonlinear diagnostic is proposed to distinguish between the saturated states of the three canonical instabilities based on their distinctive density–streamfunction and generalised vorticity–streamfunction relations.
Viscous growth and rebound of a bubble near a rigid surface
- Sébastien Michelin, Giacomo Gallino, François Gallaire, Eric Lauga
-
- Published online by Cambridge University Press:
- 03 December 2018, pp. 172-199
-
- Article
- Export citation
-
Motivated by the dynamics of microbubbles near catalytic surfaces in bubble-powered microrockets, we consider theoretically the growth of a free spherical bubble near a flat no-slip surface in a Stokes flow. The flow at the bubble surface is characterised by a constant slip length allowing us to tune the hydrodynamic mobility of its surface and tackle in one formulation both clean and contaminated bubbles as well as rigid shells. Starting with a bubble of infinitesimal size, the fluid flow and hydrodynamic forces on the growing bubble are obtained analytically. We demonstrate that, depending on the value of the bubble slip length relative to the initial distance to the wall, the bubble will either monotonically drain the fluid separating it from the wall, which will exponentially thin, or it will bounce off the surface once before eventually draining the thin film. Clean bubbles are shown to be a singular limit which always monotonically get repelled from the surface. The bouncing events for bubbles with finite slip lengths are further analysed in detail in the lubrication limit. In particular, we identify the origin of the reversal of the hydrodynamic force direction as due to the change in the flow pattern in the film between the bubble and the surface and to the associated lubrication pressure. Last, the final drainage dynamics of the film is observed to follow a universal algebraic scaling for all finite slip lengths.
Passive flight in density-stratified fluids
- Try Lam, Lionel Vincent, Eva Kanso
-
- Published online by Cambridge University Press:
- 03 December 2018, pp. 200-223
-
- Article
- Export citation
-
Leaves falling in air and marine larvae settling in water are examples of unsteady descents due to complex interactions between gravitational and aerodynamic forces. Understanding passive flight is relevant to many branches of engineering and science, ranging from estimating the behaviour of re-entry space vehicles to analysing the biomechanics of seed dispersion. The motion of regularly shaped objects falling freely in homogenous fluids is relatively well understood. However, less is known about how density stratification of the fluid medium affects passive flight. In this paper, we experimentally investigate the descent of heavy discs in stably stratified fluids for Froude numbers of order 1 and Reynolds numbers of order 1000. We specifically consider fluttering descents, where the disc oscillates as it falls. In comparison with pure water and homogeneous saltwater fluid, we find that density stratification significantly enhances the radial dispersion of the disc, while simultaneously decreasing the vertical descent speed, fluttering amplitude and inclination angle of the disc during descent. We explain the physical mechanisms underlying these observations in the context of a quasi-steady force and torque model. These findings could have significant impact on the design of unpowered vehicles and on the understanding of geological and biological transport where density and temperature variations may occur.
Slug generation processes in co-current turbulent-gas/laminar-liquid flows in horizontal channels
- Sha Miao, Kelli Hendrickson, Yuming Liu
-
- Published online by Cambridge University Press:
- 03 December 2018, pp. 224-257
-
- Article
- Export citation
-
We theoretically and computationally investigate the physical processes of slug-flow development in concurrent two-phase turbulent-gas/laminar-liquid flows in horizontal channels. The objective is to understand the fundamental mechanisms governing the initial growth and subsequent nonlinear evolution of interfacial waves, starting from a smooth stratified flow of two fluids with disparity in density and viscosity and ultimately leading to the formation of intermittent slug flow. We numerically simulate the entire slug development by means of a fully coupled immersed flow (FCIF) solver that couples the two disparate flow dynamics through an immersed boundary (IB) method. From the analysis of spatial/temporal interface evolution, we find that slugs develop through three major cascading processes: (I) stratified-to-wavy transition; (II) development and coalescence of long solitary waves; and (III) rapid channel bridging leading to slugging. In Process I, relatively short interfacial waves form on the smooth interface, whose growth is governed by the Orr–Sommerfeld instability. In Process II, interfacial waves evolve into long solitary waves through multiple resonant and near-resonant wave–wave interactions. From instability analysis of periodic solitary waves, we show that these waves are unstable to their subharmonic disturbances and grow in amplitude and primary wavelength through wave coalescence. The interfacial forcing from the turbulent gas–laminar liquid interactions significantly precipitates the growth of instability of solitary waves and enhances coalescence of solitary waves. In Process III, we show by an asymptotic analysis that interfacial waves achieve multiple-exponential growth right before bridging the channel, consistent with observations in existing experiments. The present study provides important insights for effective modelling of slug-flow dynamics and the prediction of slug frequency and length, important for design and operation of (heavy-oil/gas) pipelines and production facilities.
Turbulent flow through a high aspect ratio cooling duct with asymmetric wall heating
- Thomas Kaller, Vito Pasquariello, Stefan Hickel, Nikolaus A. Adams
-
- Published online by Cambridge University Press:
- 04 December 2018, pp. 258-299
-
- Article
- Export citation
-
We present well-resolved large-eddy simulations of turbulent flow through a straight, high aspect ratio cooling duct operated with water at a bulk Reynolds number of
$Re_{b}=110\times 10^{3}$ and an average Nusselt number of
$Nu_{xz}=371$. The geometry and boundary conditions follow an experimental reference case and good agreement with the experimental results is achieved. The current investigation focuses on the influence of asymmetric wall heating on the duct flow field, specifically on the interaction of turbulence-induced secondary flow and turbulent heat transfer, and the associated spatial development of the thermal boundary layer and the inferred viscosity variation. The viscosity reduction towards the heated wall causes a decrease in turbulent mixing, turbulent length scales and turbulence anisotropy as well as a weakening of turbulent ejections. Overall, the secondary flow strength becomes increasingly less intense along the length of the spatially resolved heated duct as compared to an adiabatic duct. Furthermore, we show that the assumption of a constant turbulent Prandtl number is invalid for turbulent heat transfer in an asymmetrically heated duct.
Fundamental equations for primary fluid recovery from porous media
- Yan Jin, Kang Ping Chen
-
- Published online by Cambridge University Press:
- 04 December 2018, pp. 300-317
-
- Article
- Export citation
-
Primary fluid recovery from a porous medium is driven by the volumetric expansion of the in situ fluid. For production from a petroleum reservoir, primary recovery accounts for more than half of the total amount of recovered hydrocarbon. The primary recovery process is studied here at the pore scale and the macroscopic scale. The pore-scale flow is first analysed using the compressible Navier–Stokes equations and the mathematical theory for low-Mach-number flow developed by Klainerman & Majda (Commun. Pure Appl. Maths, vol. 34 (4), 1981, pp. 481–524; vol. 35 (5), 1982, pp. 629–651). An asymptotic analysis shows that the pore-scale flow is governed by the self-diffusion of the fluid and it exhibits a slip-like mass flow rate, even though the velocity satisfies the no-slip condition on the pore wall. The pore-scale density equation is then upscaled to a macroscopic diffusion equation for the density which possesses a diffusion coefficient proportional to the fluid’s kinematic viscosity. Darcy’s law is shown to be inapplicable to primary fluid recovery and it should be replaced by a new mass flux equation which depends on the porosity but not on the permeability. This is in stark contrast to the classical result and it can have important implications for hydrocarbon recovery as well as other applications.
Computationally generated constitutive models for particle phase rheology in gas-fluidized suspensions
- Yile Gu, Ali Ozel, Jari Kolehmainen, Sankaran Sundaresan
-
- Published online by Cambridge University Press:
- 04 December 2018, pp. 318-349
-
- Article
- Export citation
-
Developing constitutive models for particle phase rheology in gas-fluidized suspensions through rigorous statistical mechanical methods is very difficult when complex inter-particle forces are present. In the present study, we pursue a computational approach based on results obtained through Eulerian–Lagrangian simulations of the fluidized state. Simulations were performed in a periodic domain for non-cohesive and mildly cohesive (Geldart Group A) particles. Based on the simulation results, we propose modified closures for pressure, bulk viscosity, shear viscosity and the rate of dissipation of pseudo-thermal energy. For non-cohesive particles, results in the high granular temperature
$T$ regime agree well with constitutive expressions afforded by the kinetic theory of granular materials, demonstrating the validity of the methodology. The simulations reveal a low
$T$ regime, where the inter-particle collision time is determined by gravitational fall between collisions. Inter-particle cohesion has little effect in the high
$T$ regime, but changes the behaviour appreciably in the low
$T$ regime. At a given
$T$, a cohesive particle system manifests a lower pressure at low particle volume fractions when compared to non-cohesive systems; at higher volume fractions, the cohesive assemblies attain higher coordination numbers than the non-cohesive systems, and experience greater pressures. Cohesive systems exhibit yield stress, which is weakened by particle agitation, as characterized by
$T$. All these effects are captured through simple modifications to the kinetic theory of granular materials for non-cohesive materials.
Turbulence in intermittent transitional boundary layers and in turbulence spots
- Olaf Marxen, Tamer A. Zaki
-
- Published online by Cambridge University Press:
- 05 December 2018, pp. 350-383
-
- Article
- Export citation
-
Direct numerical simulation data of bypass transition in flat-plate boundary layers are analysed to examine the characteristics of turbulence in the transitional regime. When intermittency is 50 % or less, the flow features a juxtaposition of turbulence spots surrounded by streaky laminar regions. Conditionally averaged turbulence statistics are evaluated within the spots, and are compared to standard time averaging in both the transition region and in fully turbulent boundary layers. The turbulent-conditioned root-mean-square levels of the streamwise velocity perturbations are notably elevated in the early transitional boundary layer, while the wall-normal and spanwise components are closer to the levels typical for fully turbulent flow. The analysis is also extended to include ensemble averaging of the spots. When the patches of turbulence are sufficiently large, they develop a core region with similar statistics to fully turbulent boundary layers. Within the tip and the wings of the spots, however, the Reynolds stresses and terms in the turbulence kinetic energy budget are elevated. The enhanced turbulence production in the transition zone, which exceeds the levels from fully turbulent boundary layers, contributes to the higher skin-friction coefficient in that region. Qualitatively, the same observations hold for different spot sizes and levels of free-stream turbulence, except for young spots which do not yet have a core region of developed turbulence.
The effect of vertically varying permeability on tracer dispersion
- Edward M. Hinton, Andrew W. Woods
-
- Published online by Cambridge University Press:
- 07 December 2018, pp. 384-407
-
- Article
- Export citation
-
We study the migration of a tracer within an injection-driven flow in a horizontal aquifer in which the permeability varies with depth. The permeability gradient produces a shear and this leads to lateral dispersion of the tracer. In the high permeability regions, the tracer moves substantially faster than the mean flow and eventually enters the nose region of the flow where the depth of the current is less than the depth of the aquifer. Depending on the influence of (i) the viscosity contrast between the injected fluid and the original fluid, and (ii) the vertical permeability gradient, the nose of the current may be of fixed shape or may gradually lengthen with time. This leads to a variety of patterns of dispersal of the tracer, which may either remain in the nose or cycle through the nose and be left behind. Our results illustrate the complexity of the migration of a tracer in a heterogeneous aquifer which has important implications for interpreting the results of tracer tests as may be proposed for monitoring
$\text{CO}_{2}$ or gas injected into subsurface reservoirs.
On the dynamics of a free surface of an ideal fluid in a bounded domain in the presence of surface tension
- Sergey A. Dyachenko
-
- Published online by Cambridge University Press:
- 07 December 2018, pp. 408-418
-
- Article
- Export citation
-
We derive a set of equations in conformal variables that describe a potential flow of an ideal two-dimensional inviscid fluid with free surface in a bounded domain. This formulation is free of numerical instabilities present in the equations for the surface elevation and potential derived in Dyachenko et al. (Plasma Phys. Rep. vol. 22 (10), 1996, pp. 829–840) with some restrictions on analyticity relieved, which allows to treat a finite volume of fluid enclosed by a free-moving boundary. We illustrate with a comparison of numerical simulations of the Dirichlet ellipse, an exact solution for a zero surface tension fluid. We demonstrate how the oscillations of the free surface of a unit disc droplet may lead to breaking of one droplet into two when surface tension is present.
Simulation of air–water interfacial mass transfer driven by high-intensity isotropic turbulence
- H. Herlina, J. G. Wissink
-
- Published online by Cambridge University Press:
- 07 December 2018, pp. 419-440
-
- Article
- Export citation
-
Previous direct numerical simulations (DNS) of mass transfer across the air–water interface have been limited to low-intensity turbulent flow with turbulent Reynolds numbers of
$R_{T}\leqslant 500$. This paper presents the first DNS of low-diffusivity interfacial mass transfer across a clean surface driven by high-intensity (
$1440\leqslant R_{T}\leqslant 1856$) isotropic turbulent flow diffusing from below. The detailed results, presented here for Schmidt numbers
$Sc=20$ and
$500$, support the validity of theoretical scaling laws and existing experimental data obtained at high
$R_{T}$. In the DNS, to properly resolve the turbulent flow and the scalar transport at
$Sc=20$, up to
$524\times 10^{6}$ grid points were needed, while
$65.5\times 10^{9}$ grid points were required to resolve the scalar transport at
$Sc=500$, which is typical for oxygen in water. Compared to the low-
$R_{T}$ simulations, where turbulent mass flux is dominated by large eddies, in the present high-
$R_{T}$ simulation the contribution of small eddies to the turbulent mass flux was confirmed to increase significantly. Consequently, the normalised mass transfer velocity was found to agree with the
$R_{T}^{-1/4}$ scaling, as opposed to the
$R_{T}^{-1/2}$ scaling that is typical for low-
$R_{T}$ simulations. At constant
$R_{T}$, the present results show that the mass transfer velocity
$K_{L}$ scales with
$Sc^{-1/2}$, which is identical to the scaling found in the large-eddy regime for
$R_{T}\leqslant 500$. As previously found for a no-slip interface, also for a shear-free interface the critical
$R_{T}$ separating the large- from the small-eddy regime was confirmed to be approximately
$R_{T}=500$.
Structure of the hydraulic jump in convergent radial flows
- K. A. Ivanova, S. L. Gavrilyuk
-
- Published online by Cambridge University Press:
- 07 December 2018, pp. 441-464
-
- Article
- Export citation
-
We are interested in the modelling of multi-dimensional turbulent hydraulic jumps in convergent radial flow. To describe the formation of intensive eddies (rollers) at the front of the hydraulic jump, a new model of shear shallow water flows is used. The governing equations form a non-conservative hyperbolic system with dissipative source terms. The structure of equations is reminiscent of generic Reynolds-averaged Euler equations for barotropic compressible turbulent flows. Two types of dissipative term are studied. The first one corresponds to a Chézy-like dissipation rate, and the second one to a standard energy dissipation rate commonly used in compressible turbulence. Both of them guarantee the positive definiteness of the Reynolds stress tensor. The equations are rewritten in polar coordinates and numerically solved by using an original splitting procedure. Numerical results for both types of dissipation are presented and qualitatively compared with the experimental works. The results show both experimentally observed phenomena (cusp formation at the front of the hydraulic jump) as well as new flow patterns (the shape of the hydraulic jump becomes a rotating square).
Scale-dependent alignment, tumbling and stretching of slender rods in isotropic turbulence
- Nimish Pujara, Greg A. Voth, Evan A. Variano
-
- Published online by Cambridge University Press:
- 07 December 2018, pp. 465-486
-
- Article
- Export citation
-
We examine the dynamics of slender, rigid rods in direct numerical simulation of isotropic turbulence. The focus is on the statistics of three quantities and how they vary as rod length increases from the dissipation range to the inertial range. These quantities are (i) the steady-state rod alignment with respect to the perceived velocity gradients in the surrounding flow, (ii) the rate of rod reorientation (tumbling) and (iii) the rate at which the rod end points move apart (stretching). Under the approximations of slender-body theory, the rod inertia is neglected and rods are modelled as passive particles in the flow that do not affect the fluid velocity field. We find that the average rod alignment changes qualitatively as rod length increases from the dissipation range to the inertial range. While rods in the dissipation range align most strongly with fluid vorticity, rods in the inertial range align most strongly with the most extensional eigenvector of the perceived strain-rate tensor. For rods in the inertial range, we find that the variance of rod stretching and the variance of rod tumbling both scale as
$l^{-4/3}$, where
$l$ is the rod length. However, when rod dynamics are compared to two-point fluid velocity statistics (structure functions), we see non-monotonic behaviour in the variance of rod tumbling due to the influence of small-scale fluid motions. Additionally, we find that the skewness of rod stretching does not show scale invariance in the inertial range, in contrast to the skewness of longitudinal fluid velocity increments as predicted by Kolmogorov’s
$4/5$ law. Finally, we examine the power-law scaling exponents of higher-order moments of rod tumbling and rod stretching for rods with lengths in the inertial range and find that they show anomalous scaling. We compare these scaling exponents to predictions from Kolmogorov’s refined similarity hypotheses.
The enhancement of viscous fingering with bidisperse particle suspension
- Feng Xu, Sungyon Lee
-
- Published online by Cambridge University Press:
- 07 December 2018, pp. 487-509
-
- Article
- Export citation
-
Viscous fingering is observed experimentally when a bidisperse suspension displaces air inside a Hele-Shaw cell, despite the stabilising viscosity ratio between the invading (suspension) and defending (air) phases. Careful experiments are carried out to characterise this instability by either systematically varying the large-particle concentrations
$\unicode[STIX]{x1D719}_{l0}$ at constant total concentrations
$\unicode[STIX]{x1D719}_{0}$, or changing
$\unicode[STIX]{x1D719}_{0}$ with fixed
$\unicode[STIX]{x1D719}_{l0}$. Leading to the instability, we observe that larger particles consistently enrich the fluid–fluid interface at a faster rate than small particles. This size-dependent enrichment of the interface leads to an earlier onset of the fingering instability for bidisperse suspensions, compared to their monodisperse counterpart of all small particles. In particular, even the small presence of large particles is shown to effectively lower the total particle concentration needed for fingering, compared to the all-small-particle case. We hypothesise that the key mechanism behind this enhanced viscous fingering is the size-dependent nature of shear-induced migration of particles far upstream from the interface. A reduced equilibrium model is derived based on the modified suspension balance model to verify this hypothesis, in reasonable agreement with experiments.
Dynamical similarity and universality of drop size and velocity spectra in sprays
- K. Dhivyaraja, D. Gaddes, E. Freeman, S. Tadigadapa, M. V. Panchagnula
-
- Published online by Cambridge University Press:
- 07 December 2018, pp. 510-543
-
- Article
- Export citation
-
Sprays are a class of multiphase flows which exhibit a wide range of drop size and velocity scales spanning several orders of magnitude. The objective of the current work is to experimentally investigate the prospect of dynamical similarity in these flows. We are also motivated to identify a choice of length and time scales which could lead towards a universal description of the drop size and velocity spectra. Towards this end, we have fabricated a cohort of geometrically similar pressure swirl atomizers using micro-electromechanical systems (MEMS) as well as additive manufacturing technology. We have characterized the dynamical characteristics of the sprays as well as the drop size and velocity spectra (in terms of probability density functions, p.d.f.s) over a wide range of Reynolds (
$Re$) and Weber numbers (
$We$) using high-speed imaging and phase Doppler interferometry, respectively. We show that the dimensionless Sauter mean diameter (
$D_{32}$) scaled to the boundary layer thickness in the liquid sheet at the nozzle exit (
$\unicode[STIX]{x1D6FF}_{o}$) exhibits self-similarity in the core region of the spray, but not in the outer zone. In addition, we show that global drop size spectra in the sprays show two distinct characteristics. The spectra from varying
$Re$ and
$We$ collapse onto a universal p.d.f. for drops of size
$x$ where
$x/\unicode[STIX]{x1D6FF}_{o}>1$. For
$x/\unicode[STIX]{x1D6FF}_{o}<1$, a residual effect of
$Re$ and
$We$ persists in the size spectra. We explain this characteristic by the fact that the physical mechanisms that cause large drops is different from that which is responsible for the small drops. Similarly, with the liquid sheet velocity at the nozzle exit (
$u_{s}$) as the choice of velocity scale, we show that drops moving with a velocity
$u$ such that
$u/u_{s}<1$ collapse onto a universal p.d.f., while drops with
$u/u_{s}>1$ exhibit a residual effect of
$Re$ and
$We$. From these observations, we suggest that physically accurate models for drop size and velocity spectra should rely on piecewise descriptions of the p.d.f. rather than invoking a single mathematical form for the entire distribution. Finally, we show from a dynamical modal analysis that the conical liquid sheet flapping characteristics exhibit a sharp transition in Strouhal number (
$St$) at a critical
$Re$.