In this paper, a new design of an optoelectronic system for transient waveforms shaping, with a selection of rejected frequencies, is presented. The generation of short pulses is performed with several optoelectronic generators using photoconductive semiconductor switches (PCSS) operating in linear switching mode and triggered via a laser pulse. With the appropriate number of generators, the system generates a spectrum ranging from 300 MHz to 3 GHz, with rejected frequencies at 900 MHz and 1.8 GHz. A PCSS characterization has been set up to determine the necessary parameters for the establishment of an optoelectronic generator model on Keysight Advanced Design System software (ADS). Experimental tests have been realized using measurement benches to compare the simulated and measured signals.

The implementation of advanced multi-level modulation schemes such as quadrature phase-shift keying (QPSK) in contrast to the conventional on–off keying is crucial to further boost the terahertz (THz) communications speed. Thereby, carrier phase noise reduction in the THz range is one of the key goals that need to be urgently achieved. In this paper, the photonic-based THz sources and the phase noise problem are briefly summarized. Then, a low phase-noise photonic source based on the stimulated Brillouin scattering (SBS) optical fiber cavity is first applied for a 300-GHz-band QPSK wireless communication link. The highest data rate at forward-error-correction limited condition was 15 Gbaud utilizing the SBS-based photonic source with a small transmit power of ~ −36 dBm. Its transmission characteristics are evaluated and compared with the conventional optical frequency comb generator (OFCG)-based source at 5 Gbaud. The proposed SBS-based photonic source has been proven to offer better performances than the OFCG-based source with respect to the phase noise, optical carrier to noise ratio, and bit error rate in communications.

A growing interest in dielectric waveguides (DWGs) as an alternative to commonly used waveguides (like coaxial or twisted-pair cables) for high data rate interconnects could be observed in the last few years. Especially in the mm-wave frequency range (30–300 GHz) applications with these waveguides benefit from low losses and low dispersion. Moreover, using both polarizations of the fundamental mode in such waveguides could theoretically double the data rate without the need of higher bandwidth or additional fibers. The connection between DWGs and commonly available transceiver chips requires broadband transitions from planar waveguides like microstrip lines to DWGs. In this paper, an overview of the current developments of such transitions is given and a novel low-complexity design is presented that reduces the space consumption by 35% related to recently published works. This allows an easy integration into a printed circuit board layout or a chip package. Furthermore, an extensive sensitivity analysis is presented to prove the robustness toward manufacturing tolerances. The transition is realized at W-band frequencies (75–110 GHz) and achieves a relative 10 dB-bandwidth of more than 25% with a minimum insertion loss of 1.2 dB. It is shown that these properties even hold for manufacturing tolerances of nowadays manufacturing processes.

This paper presents a novel GaN-based digital outphasing power amplifier (PA) for the 800 MHz range. The PA reaches a maximum output power of 5.8 W at 30 V final-stage (FS) drain supply voltage. A novel output combiner circuit is used and efficiency is improved by resonant commutation of the FSs and optimized driver circuits for the two GaN push-pull FSs. 3D electromagnetic simulation of output network has been conducted to extract an equivalent circuit model and to access full information in terms of functionality and broadband impedance characteristics for optimized outphasing operation in the final design. Measured total efficiencies (ηtot) of 59 and 25% at 0 and 10 dB power back-off are achieved, respectively, fitting the simulation quite well. The proposed digital outphasing module is a promising candidate for fully digitized base-station architectures in future wireless communications.

A superheterodyne transmission scheme is adopted and analyzed in a 300 GHz wireless point-to-point link. This was realized using two different intermediate frequency (IF) systems. The first uses fast digital synthesis which provides an IF signal centered around a carrier frequency of 10 GHz. The second involves the usage of commercially available mixers, which work as direct up- and down-converters, to generate the IF input and output. The radio frequency components are based on millimeterwave monolithic integrated circuits at a center frequency of 300 GHz. Transmission experiments over distances up to 10 m are carried out. Data rates of up to 60 Gbps using the first IF option and up to 24 Gbps using the second IF option are achieved. Modulation formats up to 32QAM are successfully transmitted. The linearity of this link and of its components is analyzed in detail. Two local oscillators (LOs), a photonics-based source and a commercially available electronic source are employed and compared. This work validates the concept of superheterodyne architecture for integration in a beyond-5G network, supplying important guidelines that have to be taken into account in the design steps of a future wireless system.

This paper proposes a differential sensor based on a pair of open split ring resonators (OSRR) operating in reflection. The output signal is thus the differential reflection coefficient of both resonators, intimately related to their dielectric loading. Thus, for identical loads in both sensing resonators, the individual reflection coefficients are equal, thereby providing an ideally null output signal. By contrast, when unequal dielectric loads truncate the symmetry, the reflection coefficients are different, resulting in a differential output signal related to the level of asymmetry. In order to ease the measurement of the output signal, a rat-race hybrid coupler is used. The OSRR sensing loads are connected to the coupled ports of the hybrid coupler, whereas the input signal is injected to the Δ-port, and the output signal is collected at the isolated port (Σ-port). By this means, the output signal, i.e. the differential reflection coefficient between both sensing loads, is obtained from the transmission coefficient of a simple two-port structure. For experimental validation purposes, the sensor is applied to the measurement of isopropanol content in aqueous solutions, and for that purpose, the sensitive regions are equipped with microfluidic channels.

Electromagnetic scattering from the sea surface is of great significance in radar detection, target recognition, ocean remote sensing, etc. By introducing the action spectrum, the modified spatio-temporal variation wave spectrum is used to establish a nonlinear sea surface with currents in this paper. Traditional capillary wave modification facet scattering model (CWMFSM) can only calculate the backscattering from the wind-driven sea surface. By using the new spatio-temporal variation wave spectrum to modify the scattering amplitude of every facet, the new CWMFSM can be used to calculate the nonlinear sea surface scattering with surface currents. Therefore, the model simultaneously considers the modulation of sea surface wind and currents to the radar back echo. The dependence of backscattering coefficient from nonlinear sea surface on the incident angle and the polarization are discussed. The results verify that the nonlinear model is more consistent with the measurement data. This paper also investigates the Doppler spectrum characteristics of the sea with currents. It is found that the effect of wave–current interaction on Doppler spectra is weaker than that of wave–wave interaction. The SAR images of nonlinear sea surfaces are also simulated and different bands, polarizations, and baseline length effects on sea current detection performance of along-track interference SAR are analyzed.

This paper reports on quasi-elliptic dual-band bandpass filters (BPFs) that were designed for the Filter Student Design Competition of the 2019 European Microwave Week. The proposed lumped-element (LE) BPF concept is based on two dual-band transversal cells and one multi-resonant cell that allow the realization of symmetric and asymmetric dual-band transfer functions shaped by six poles and five transmission zeros. A compact implementation scheme based on LE series resonators is proposed for size compactness and wide spurious free out-of-band response. For proof-of-concept demonstration purposes, a dual-band LE prototype with two passbands centered 1 and 1.5 GHz was designed, manufactured, and measured. It exhibited the following radio frequency measured performance characteristics. Passbands centered at 1.02 and 1.45 GHz, minimum insertion loss levels of 2.0 and 2.7 dB, and bandwidth of 146 and 105 MHz, respectively, for the first and the second passband, and out-of-band rejection >30 dB between 0 and 894 MHz, 1.17–1.34 GHz, and 1.72–6.9 GHz.

The effective resistivity (ρeff) is a figure of merit commonly used to assess the radio-frequency performance of a substrate from the measurements of coplanar waveguide lines. For highly resistive substrates, such as the trap-rich (TR) substrate, the extracted ρeff decreases by several orders of magnitude at millimeter-wave frequencies. The explanation for this decay is twofold. First, the imaginary part of the characteristic impedance ${\rm \lpar \Im }\lpar Z_c\rpar \rpar$ is not well extracted, which leads to an incorrect separation of the total losses among the metal and substrate losses. Second, the original expression of ρeff does not include dielectric losses, which might become non-negligible at millimeter-wave frequencies. This paper solves both issues by presenting a new procedure to extract ρeff and the dielectric losses simultaneously, and by introducing a novel method to correct ${\rm \Im }\lpar {Z_c} \rpar$. Furthermore, it is shown that this extraction method enables the correct extraction of substrate parameters up to 220 GHz of TR and high-resistivity silicon substrates. Finally, the origin of the large extracted value of dielectric loss is discussed in the potential presence of surface roughness and surface wave radiation. Both phenomena are discounted thanks to measurements of an additional reflective structure and a standard impedance substrate.

This paper presents the filter design in the student design competition of EuMW 2019. This contest motivates students for the design and implementation of a dual-band bandpass filter able to get outstanding performance, where different implementation technologies, such as microstrip, coplanar, multilayer microstrip, substrate integrated waveguide, and some others can be effectively employed. Filters are evaluated by considering a figure of merit (FoM) defined by the insertion loss level, selectivity, spurious-free response, and size. To this end, three viable dual-band bandpass filters with different feeding technologies, resonators, and design topologies are investigated for the optimal FoM.

Microwave imaging is an efficient technique that can be used for the early detection of breast cancer. Therefore the current research article presents the microwave imaging of two spherical tumors (radius 4 and 5 mm) in the breast phantom by using the monostatic radar-based technique. This is carried out by using an ultra-wideband (4.9–10.9 GHz), three-layered stacked aperture coupled microstrip antenna (SACMPA) with a defected ground structure to scan the breast phantom and make near field S parameter measurements from a breast phantom. The S parameter data from different locations and at different time intervals are noted and then used in a beam-forming algorithm; Delay and Sum to process it and form a 2D image of the tumor location in the breast phantom using MATLAB.

The proposed SACMPA is a three-layered structure with overall dimensions of 37 × 43 × 4.85 mm3 that shows an impedance bandwidth of 6 GHz (4.9–10.9 GHz) and a simulated peak gain of 6.32 dB at a frequency of 9.1 GHz. The validation of S parameters and gain results are done using a Vector Network Analyzer (VNA) and an anechoic chamber. The experimental validation of the proposed microwave imaging procedure is done by allowing the SACMPA to radiate parallel to the breast phantom made from polythene (skin), petroleum jelly (fat), and wheat flour (with water as tumor) and record the S parameters on the VNA. The proposed microwave method is safe for human exposure as the antenna also shows simulated specific absorption rates of 0.271 and 1.115 W/Kg (on the breast phantom) at frequencies of 5.7 and 6.5 GHz, respectively (for 1 g of body tissue).

This paper presents a novel dual-band (DB) dual-polarized (DP) shared aperture antenna with high isolation by using a combination of microstrip dipoles and dielectric resonator antennas (DRAs) for S and C bands, respectively. In the S band, two sets of proximity coupled stacked microstrip dipoles which crossed at the center are employed to achieve dual-linear polarization (DLP) and obtain desired bandwidth (BW), isolation, and pure polarization. The rectangle DRA with hybrid feed is selected as the C band element for its advantages of small base area and high isolation, and a 2 × 2 array is presented with the “pair-wise” anti-phase feed technique to achieve a low cross-polarized level. Moreover, benefited from the back feed scheme, the proposed antenna has a symmetrical structure and has the potential of expanding into a larger aperture. The proposed antenna has been manufactured and measured, and the results agree well with simulations, which prove the validity of the proposed design.

In this work, we proposed an adaptive beamformer based on a novel heuristic optimization algorithm. The novel optimization technique inspired from Fibonacci sequence principle, designated as Fibonacci branch search (FBS), used new tree's branches fundamental structure and interactive searching rules to obtain the global optimal solution in the search space. The branch structure of FBS is selected using two types of multidimensional points on the basis of shortening fraction formed by Fibonacci sequence; in this mode, interactive global and local searching rules are implemented alternately to obtain the optimal solutions, avoiding stagnating in local optimum. The proposed FBS is also used here to construct an adaptive beamforming (ABF) technique as a real-time implementation to achieve near-optimal performance for its simplicity and high convergence rate, then, the performance of the FBS is compared with the five typical heuristic optimization algorithms. Simulation results demonstrate the superiority of the proposed FBS approach in locating the optimal solution with higher precision and reveal further improvement in the ABF performance.

In this paper, a high gain wideband circularly polarized (CP) microstrip antenna is presented for broadband operation. The proposed structure comprised of a partially grounded printed monopole antenna loaded with a split ring resonator and a metallic reflector. By using the metallic reflector surface underneath the patch radiator results in the reflected waves in the same phase with main lobe radiation, thereby improving the gain and it also acts like a secondary radiator to generate wideband CP behavior in the proposed design. A gain enhancement of 4.3 dBi is achieved in the operating frequency band as compared with the design without a metallic reflector. The maximum gain achieved in the presented method is 8.6 dBic over the entire operating range. The proposed design shows a wideband behavior ranging from 4.30 to 9.10 GHz with the 10-dB impedance bandwidth of 71.64%. In addition, the proposed design yielded a broadside right hand CP radiation with a 3-dB axial ratio bandwidth of 33.88% from 4.98 to 7.01 GHz. The proposed antenna is fabricated and experimental results on reflection coefficient, gain, axial ratio, and radiation patterns concede well with simulation results.

In this paper, an antenna-to-antenna method to design high-efficiency polarization converters was proposed. Two in-linked split ring resonators (SRRs) were used as the fundamental unit cell, which can effectively make the original linear polarization angle deflected into a customized one (include but not limited to 90°). The same as the process of energy reception and transmitting of microstrip symmetric dipole antennas, the top SRR plays the role of a receiving antenna and the bottom one acts as a transmitting antenna. Under normal illumination, the strong coupling between electric resonance and magnetic resonance can result in high transmission and broad bandwidth. Since the two SRRs act as two independently polarization selective components, the polarization angle of transmitted waves can be easily controlled by rotating the transmitting SRRs around the center. The proposed concept and the design method are validated using numerical simulations, as well as experimental results of three examples for 45, 60 and 90° polarization angle rotation, the polarization conversion ratio of which is about 92.2, 88.9 and 91.9% from 7.5 to 10 GHz.