Hostname: page-component-586b7cd67f-r5fsc Total loading time: 0 Render date: 2024-11-24T11:03:11.574Z Has data issue: false hasContentIssue false
  • English
  • Français

Observation and numerical simulation of an elastic-plastic solid loaded by a spherical indenter

Published online by Cambridge University Press:  01 December 2004

Naoki Fujisawa ,
Wei Li  and
Michael V. Swain
Naoki Fujisawa*
Affiliation:
School of Physics, University of Sydney, NSW 2006, Australia
Wei Li
Affiliation:
School of Aerospace, Mechanical and Mechatronic Engineering, University of Sydney, NSW 2006, Australia
Michael V. Swain
Affiliation:
School of Aerospace, Mechanical and Mechatronic Engineering, University of Sydney, NSW 2006, Australia; and Biomaterials Science Research Unit, Faculty of Dentistry, University of Sydney, United Dental Hospital, Surry Hills, NSW 2010, Australia
*
a) Address all correspondence to this author. e-mail: naoki@physics.usyd.edu.au
Get access

Abstract

The observation and finite element simulation of Ti–6Al–4V loaded by a spherical indenter were compared. The contact radius at the maximum load was 40% of the indenter radius, which resulted in a high degree of plasticity induced beneath the indenter. The spherical impression profile predicted by the simulation was in agreement with that of the observation. The local curvature of the spherical impression was shown to vary with radial distance. The overall curvature change with radial distance was more distinctive in the presence of static friction. Due to the large plastic zone in the material, neither the Field–Swain nor the Oliver–Pharr method was able to predict the elastic recovery depths in the center of indentation and at the perimeter of contact. The ratio of the two depths predicted by the latter method, however, may be used to verify the applicability of the method itself in determining the elastic modulus of a ductile material.

Keywords

Computer simulationMetalNanoindentation
Type
Articles
Information
Journal of Materials Research , Volume 19 , Issue 12 , December 2004 , pp. 3474 - 3483
Copyright
Copyright © Materials Research Society 2004

Access options

Get access to the full version of this content by using one of the access options below. (Log in options will check for institutional or personal access. Content may require purchase if you do not have access.)

References

REFERENCES

1Weppelman, E.R. and Swain, M.V.: Investigation of the stresses and stress intensity factors responsible for fracture of thin protective films during ultra-micro indentation tests with spherical indenters. Thin Solid Films 286, 111 (1996).CrossRefGoogle Scholar
2Bolshakov, A. and Pharr, G.M.: Influences of pileup on the measurement of mechanical properties by load and depth-sensing indentation techniques. J. Mater. Res. 13, 1049 (1998).CrossRefGoogle Scholar
3Begley, M.R., Evans, A.G. and Hutchinson, J.W.: Spherical impression of thin elastic films on elastic-plastic substrates. Int. J. Solids Struct. 36, 2773 (1999).CrossRefGoogle Scholar
4Mesarovic, S.D. and Fleck, N.A.: Spherical indentation of elastic-plastic solids. Proc. R. Soc. Lond. A 455, 2707 (1999).CrossRefGoogle Scholar
5Chudoba, T., Schwarzer, N. and Richter, F.: New possibilities of mechanical surface characterization with spherical indenters by comparison of experimental and theoretical results. Thin Solid Films 355–356, 284 (1999).CrossRefGoogle Scholar
6Zeng, K. and Chiu, C-h.: An analysis of load-penetration curves from instrumented indentation. Acta Mater. 49, 3539 (2001).CrossRefGoogle Scholar
7Matsuda, K.: Prediction of stress-strain curves of elastic-plastic materials based on the Vickers indentation. Philos. Mag. A 82, 1941 (2002).CrossRefGoogle Scholar
8Thurn, J., Morris, D.J. and Cook, R.F.: Depth-sensing indentation at macroscopic dimensions. J. Mater. Res. 17, 2679 (2002).CrossRefGoogle Scholar
9Thurn, J. and Cook, R.F.: Indentation-induced deformation at ultramicroscopic and macroscopic contacts. J. Mater. Res. 19, 124 (2004).CrossRefGoogle Scholar
10Johnson, A.E.Jr., Mechanical properties at room temperature of four cermets of tungsten carbide with cobalt binder, Technical Note 3309 of National Advisory Committee For Aeronautics (Langley Aeronautical Laboratory, Langley Field, VA, 1954)Google Scholar
11Field, J.S. and Swain, M.V.: A simple predictive model for spherical indentation. J. Mater. Res. 8, 297 (1993).CrossRefGoogle Scholar
12Sneddon, I.N.: The relation between load and penetration in the axisymmetric Boussinesq problem for a punch of arbitrary profile. Int. J. Eng. Sci. 3, 47 (1965).CrossRefGoogle Scholar
13Loubet, J.L., Georges, J.M., Marchesini, O. and Meille, G.: Vickers indentation curves of magnesium oxide (MgO). J. Tribology 106, 43 (1984).CrossRefGoogle Scholar
14Pharr, G.M., Oliver, W.C. and Brotzen, F.R.: On the generality of the relationship among contact stiffness, contact area, and elastic modulus during indentation. J. Mater. Res. 7, 613 (1992).CrossRefGoogle Scholar
15Titanium Alloys, Materials Properties Handbook, edited by Boyer, R., Welsch, G., and Collings, E.W. (ASM International, Materials Park, OH, 1994)Google Scholar
16Oliver, W.C. and Pharr, G.M.: An improved technique for determining hardness and elastic modulus using load and displacement sensing indentation experiments. J. Mater. Res. 7, 1564 (1992).CrossRefGoogle Scholar