Crossref Citations
This article has been cited by the following publications. This list is generated based on data provided by
Crossref.
Hsueh, C. H.
2002.
Devising a method to measure film adhesion through modeling.
Applied Physics Letters,
Vol. 81,
Issue. 9,
p.
1615.
Im, J.
Townsend, P. H.
Curphy, J.
Karas, C.
and
Shaffer, E. O.
2002.
Metallization of Polymers 2.
p.
53.
Roham, Sassan
Hardikar, Kedar
and
Woytowitz, Peter
2004.
Crack penetration and deflection at a bimaterial interface in a four-point bend test.
Journal of Materials Research,
Vol. 19,
Issue. 10,
p.
3019.
Damayanti, M.
Widodo, J.
Sritharan, T.
Mhaisalkar, S.G.
Lu, W.
Gan, Z.H.
Zeng, K.Y.
and
Hsia, L.C.
2005.
Adhesion study of low-k/Si system using 4-point bending and nanoscratch test.
Materials Science and Engineering: B,
Vol. 121,
Issue. 3,
p.
193.
Widodo, J.
Damayanti, M.
Mhaisalkar, S.G.
Lu, W.
Ong, S.
Sritharan, T.
Zeng, K.Y.
and
Hsia, L.C.
2005.
Adhesion study of tetra methyl cyclo tetra siloxanes (TMCTS) and tri methyl silane (3MS)-based low-k films.
Microelectronic Engineering,
Vol. 81,
Issue. 1,
p.
35.
Damayanti, M.
Widodo, J.
Sritharan, T.
Mhaisalkar, S.G.
Lu, W.
Gan, Z.H.
Zeng, K.Y.
and
Hsia, L.C.
2005.
Erratum to “Adhesion study of low-k/Si system using 4-point bending and nanoscratch test” [Mater. Sci. Eng. B 121 (3) (2005) 193–198].
Materials Science and Engineering: B,
Vol. 122,
Issue. 3,
p.
249.
Chang, Shou-Yi
Chang, Ting-Kui
and
Lee, Yu-Shuien
2005.
Nanoindentating Mechanical Responses and Interfacial Adhesion Strength of Electrochemically Deposited Copper Film.
Journal of The Electrochemical Society,
Vol. 152,
Issue. 10,
p.
C657.
Roham, S.
and
Hight, T.
2007.
Role of residual stress on crack penetration and deflection at a bimaterial interface in a 4-point bend test.
Microelectronic Engineering,
Vol. 84,
Issue. 1,
p.
72.
Tada, M.
Abe, M.
Furutake, N.
Ito, F.
Tonegawa, T.
Sekine, M.
and
Hayashi, Y.
2007.
Improving Reliability of Copper Dual-Damascene Interconnects by Impurity Doping and Interface Strengthening.
IEEE Transactions on Electron Devices,
Vol. 54,
Issue. 8,
p.
1867.
Shaw, T. M.
Liniger, E.
Bonilla, G.
Doyle, J. P.
Herbst, B.
Liu, X. H.
and
Lane, M. W.
2007.
Experimental Determination of the Toughness of Crack Stop Structures.
p.
114.
Kim, B.R.
Kim, Y.D.
Moon, M.S.
Choi, B.K.
and
Ko, M.J.
2008.
Adhesion properties of polymethylsilsesquioxane based low dielectric constant materials by the modified edge lift-off test.
Microelectronic Engineering,
Vol. 85,
Issue. 1,
p.
74.
Takeda, Masaaki
Matoba, Nobuhiro
Oishi, Manabu
and
Sakai, Mototsugu
2008.
Evaluation of Adhesion Between UV-cured SiOC Film and Si Substrate by Nanoindentation Method.
MRS Proceedings,
Vol. 1116,
Issue. ,
Kim, B.R.
and
Ko, M.J.
2009.
The assessment of the fracture behavior in spin-on organosilicates by nanoindentation and nanoscratch tests.
Thin Solid Films,
Vol. 517,
Issue. 11,
p.
3216.
Takeda, M.
Matoba, N.
Matsuda, K.
Seki, H.
Inoue, K.
Oishi, M.
and
Sakai, M.
2010.
Effect of ultraviolet cure on the interfacial toughness and structure of SiOC thin film on Si substrate.
Journal of Materials Research,
Vol. 25,
Issue. 10,
p.
1910.
Lei, Wei‐Sheng
and
Kumar, Ajay
2014.
Adhesion in Microelectronics.
p.
33.
Lei, Wei‐Sheng
Mittal, Kash
and
Kumar, Ajay
2016.
Medical Coatings and Deposition Technologies.
p.
631.
Lakhera, Nishant
Howell, Jim
Kipperman, Scott
Welsh, Evan
and
Schmadlak, Ilko
2017.
Strength characterization of TEOS and FTEOS interlayer dielectric materials to compare fracture risk in die stack by 3D FE simulation approach.
p.
1.
Cioban, Max
Sinha, Tuhin
and
Shaw, Thomas M.
2018.
Back-end-of-Line (BEOL) Mechanical Integrity Evaluation: A Mixed-Mode Double Cantilever Beam Test for Crackstop Strength Assessment.
p.
467.
Rabie, Mohamed
Polomoff, Nicholas A.
Hassan, Md Khaled
Calero-DdelC, Victoria L.
Degraw, Danielle
Hecker, Michael
Thiele, Michael
and
Bazizi, El Mehdi
2018.
Innovative Design of Crackstop Wall for 14nm Technology Node and Beyond.
p.
460.
Polomoff, Nicholas Alexander
and
Rabie, Mohamed A.
2021.
The Influence of Layer thickness on Crackstops' Mechanical Strength and Robustness.
p.
62.