Hostname: page-component-848d4c4894-xfwgj Total loading time: 0 Render date: 2024-07-07T05:17:36.241Z Has data issue: false hasContentIssue false
  • English
  • Français

Self-propagating high-temperature synthesis of TiC and NbC by mechanical alloying

Published online by Cambridge University Press:  03 March 2011

Z.G. Liu ,
L.L. Ye ,
J.T. Guo ,
G.S. Li  and
Z.Q. Hu
Z.G. Liu*
Affiliation:
National Key Lab for RSA, Institute of Metal Research, Academia Sinica, Shenyang 110015, China
L.L. Ye
Affiliation:
National Key Lab for RSA, Institute of Metal Research, Academia Sinica, Shenyang 110015, China
J.T. Guo
Affiliation:
Department of Superalloy and Special Casting, Institute of Metal Research, Academia Sinica, Shenyang 110015, China
G.S. Li
Affiliation:
National Key Lab for RSA, Institute of Metal Research, Academia Sinica, Shenyang 110015, China
Z.Q. Hu
Affiliation:
National Key Lab for RSA, Institute of Metal Research, Academia Sinica, Shenyang 110015, China
*
a)Address all correspondence to this author.
Get access

Abstract

Titanium and niobium carbides have been synthesized through self-propagating high-temperature reaction by mechanically alloying the elemental powder mixtures. It is found that this reaction is very similar to the conventional self-propagating high-temperature synthesis (SHS) process, but the ignition of the reaction is identified to be the mechanical collisions instead of heating the materials. Analysis of the products reveals that the final products of the Ti-C system are in good agreement with the equilibrium phase diagram, showing less relation with the alloying process. The decrease of the C content shortens the milling time prior to the SHS reaction of TiC by promoting the intimate mixing of the components, but lowers the heat release of the reaction and makes the propagation of the reaction more slowly. The SHS reaction during the mechanical alloying of the Nb-C system shows little difference, but the decrease of the C content can hardly influence the milling time prior to the reaction. By lowering the heat release of the SHS reaction of NbC, it lowers the reaction propagating rate. Mechanical alloying Nb50C50 and Nb55C45 results in the formation of NbC, while mechanical alloying Nb60C40 results in NbC + Nb instead of NbC + Nb2C according to the phase diagram. It was attributed to the fact that the rapid SHS reaction favors the formation of NbC, but hinders the occurrence of Nb2C phase through slow diffusion between NbC and the residual Nb. The measurement of the lattice parameters of TiC and NbC for different composition affirms the observed results. The particle sizes of obtained TiC and NbC are very fine at around or even less than 1 μm.

Type
Articles
Information
Journal of Materials Research , Volume 10 , Issue 12 , December 1995 , pp. 3129 - 3135
Copyright
Copyright © Materials Research Society 1995

Access options

Get access to the full version of this content by using one of the access options below. (Log in options will check for institutional or personal access. Content may require purchase if you do not have access.)

References

REFERENCES

1Toth, L. E., Transition Metal Carbides and Nitrides (Academic Press, New York, London, U.K., 1971).Google Scholar
2Biswas, D.R., J. Mater. Sci. 24, 3791 (1989).CrossRefGoogle Scholar
3Thadhani, N.N., Prog. Mater. Sci. 37, 117 (1993).CrossRefGoogle Scholar
4Munir, Z.A., Ceram. Bull. 67, 342 (1988).Google Scholar
5Benjamin, J.S. and Volin, T.E., Metall. Trans. 5, 1930 (1974).Google Scholar
6Benjamin, J.S., Metall. Trans. 1, 2943 (1970).CrossRefGoogle Scholar
7Gilman, P. S. and Benjamin, J. S., Annu. Rev. Mater. Sci. 13, 279 (1983).CrossRefGoogle Scholar
8Johnson, W.L., Prog. Mater. Sci. 30, 81 (1986).CrossRefGoogle Scholar
9Atzmon, M., Phys. Rev. Lett. 64, 487 (1990).CrossRefGoogle Scholar
10Radlinski, A. D. and Calka, A., Mater. Sci. Eng. A134, 137 (1991).Google Scholar
11Le Caer, G., Bauer-Grosse, E., Pianilli, A., Bouzy, E., and Matteazzi, P., J. Mater. Sci. 25, 4726 (1990).CrossRefGoogle Scholar
12Matteazzi, P. and Le Caer, G., J. Am. Ceram. Soc. 74, 1382 (1991).CrossRefGoogle Scholar
13Ma, E., Pagán, J., Cranford, G., and Atzmon, M., J. Mater. Res. 8, 1836 (1993).CrossRefGoogle Scholar
14Patankar, S. N., Xiao, S-Q., Lewandowski, J. J., and Heuer, A. H., J. Mater. Res. 8, 1311 (1993).CrossRefGoogle Scholar
15Hultgren, R., Desai, P. D., Hawkins, D. T., Gleiser, M., and Kelley, K. K., Selected Values of the Thermodynamic Properties of Binary Alloys (ASM, Metals Park, OH, 1973).Google Scholar
16Liu, Z. G., Guo, J. T., Ye, L. L., Li, G. S., and Hu, Z. Q., Appl. Phys. Lett. 65, 2666 (1994).CrossRefGoogle Scholar
17Munir, Z. A. and Anselmi-Tamburini, U., Mater. Sci. Rep. 3, 277 (1989).CrossRefGoogle Scholar
18Holt, J. B. and Munir, Z. A., J. Mater. Sci. 21, 251 (1986).CrossRefGoogle Scholar
19Storms, E. K., The Refractory Carbides (Academic Press, New York and London, 1967), pp. 8, 72, 67.Google Scholar