Hostname: page-component-cd9895bd7-lnqnp Total loading time: 0 Render date: 2024-12-24T16:15:30.591Z Has data issue: false hasContentIssue false
  • English
  • Français

The Influence of Diameter-to-Thickness Ratios on the Response and Collapse of Sharp-Notched Circular Tubes under Cyclic Bending

Published online by Cambridge University Press:  09 August 2012

K.-L. Lee ,
C.-M. Hsu  and
W.-F. Pan
K.-L. Lee
Affiliation:
Department of Computer Application Engineering, Far East University, Tainan County, Taiwan 74448, R.O.C.
C.-M. Hsu
Affiliation:
Department of Interior Design, Tung Fang Design University, Kaohsiung, Taiwan 82941, R.O.C.
W.-F. Pan*
Affiliation:
Department of Engineering Science, National Cheng Kung University, Tainan, Taiwan 70101, R.O.C.
*
*Corresponding author (pan@phoebus.es.ncku.edu.tw)
Get access

Abstract

This paper discusses an experimental investigation of the behavior of sharp-notched circular tubes subjected to cyclic bending. The sharp-notched circular tubes of 304 stainless steel with three different diameter-to-thickness ratios (Do / t) were tested under symmetric curvature-controlled cyclic bending. It has been shown that the moment-curvature curves exhibited the loops with cyclic hardening and gradually becoming steady after a few cycles for all tested tubes. The ovalization-curvature curves revealed unsymmetric, ratcheting and increasing behavior with the number of cycles. In addition, five almost parallel lines corresponding to five different notch depths for each Do / t ratio were found from the experimental relationship between the cyclic controlled curvature and the number of cycles necessary to produce buckling on a log-log scale. Finally, an empirical relationship was proposed so it could be used for simulating the aforementioned relationship. By comparing with the experimental finding, the derived empirical relationship was in good agreement with the experimental data.

Keywords

Sharp-notched circular tubesDiameter-to-thickness ratiosCyclic bendingMomentCurvatureOvalizationCollapse
Type
Articles
Information
Journal of Mechanics , Volume 28 , Issue 3 , September 2012 , pp. 461 - 468
Copyright
Copyright © The Society of Theoretical and Applied Mechanics, R.O.C. 2012

Access options

Get access to the full version of this content by using one of the access options below. (Log in options will check for institutional or personal access. Content may require purchase if you do not have access.)

References

REFERENCES

1. Kyriakides, S. and Shaw, P. K., “Response and Stability of Elastoplastic Circular Pipes Under Combined Bending and External Pressure,” International Journal of Solids and Structures, 18, pp. 957–973 (1982).CrossRefGoogle Scholar
2. Shaw, P. K. and Kyriakides, S., “Inelastic Analysis of Thin-Walled Tubes Under Cyclic Bending,” International Journal of Solids and Structures, 21, pp. 1073–1110 (1985).CrossRefGoogle Scholar
3. Kyriakides, S. and Shaw, P. K., “Inelastic Buckling of Tubes Under Cyclic Loads,” Journal of Pressure Vessel and Technology, ASME, 109, pp. 169–178 (1987).CrossRefGoogle Scholar
4. Corona, E. and Kyriakides, S., “On the Collapse of Inelastic Tubes Under Combined Bending and Pressure,” International Journal of Solids and Structures, 24, pp. 505–535 (1988).CrossRefGoogle Scholar
5. Corona, E. and Kyriakides, S., “An Experimental Investigation of the Degradation and Buckling of Circular Tubes Under Cyclic Bending and External Pressure,” Thin-Walled Structures, 12, pp. 229–263 (1991).CrossRefGoogle Scholar
6. Corona, E. and Vaze, S., “Buckling of Elastic-Plastic Square Tubes Under Bending,” International Journal of Mechanical Sciences, 38, pp. 753–775 (1996).CrossRefGoogle Scholar
7. Vaze, S. and Corona, E., “Degradation and Collapse of Square Tubes Under Cyclic Bending,” Thin-Walled Structures, 31, pp. 325–341 (1998).CrossRefGoogle Scholar
8. Kyriakides, S. and Lee, L. H., “Buckle Propagation in Confined Steel Tubes,” International Journal of Mechanical Science, 47, pp. 603–620 (2005).CrossRefGoogle Scholar
9. Corona, E., Lee, L. H. and Kyriakides, S., “Yield Anisotropic Effects on Buckling of Circular Tubes Under Bending,” International Journal of Solids and Structures, 43, pp. 7099–7118 (2006).CrossRefGoogle Scholar
10. Kyriakides, S., Ok, A. and Corona, E., “Localization and Propagation of Curvature Under Pure Bending in Steel Tubes with Lüders Bands,” International Journal of Solids and Structures, 45, pp. 3074–3087 (2006).CrossRefGoogle Scholar
11. Limam, A., Lee, L. H., Corana, E. and Kyriakides, S., “Plastic Buckling and Collapse of Tubes Under Bending and Internal Pressure,” Proceeding of the 27th international Conference on Offshore Mechanics and Arctic Engineering, June, Estoril, Portugal (2008).Google Scholar
12. Sakakibara, N., Kyriakides, S. and Corona, E., “Collapse of Partially Corrodes or Worn Pipe Under External Pressure,” International Journal of Mechanical Science, 50, pp. 1586–1597 (2008).CrossRefGoogle Scholar
13. Pan, W. F., Wang, T. R. and Hsu, C. M., “A Curvature-Ovalization Measurement Apparatus for Circular Tubes Under Cyclic Bending,” Experimental Mechanics, 38, pp. 99–102 (1998).CrossRefGoogle Scholar
14. Pan, W. F. and Fan, C. H., “An Experimental Study on the Effect of Curvature-Rate at Preloading Stage on Subsequent Creep or Relaxation of Thin-Walled Tubes Under Pure Bending,” JSME International Journal, Series A, 41, pp. 525–531 (1998).CrossRefGoogle Scholar
15. Pan, W. F. and Her, Y. S., “Viscoplastic Collapse of Thin-Walled Tubes Under Cyclic Bending,” Journal of Engineering Materials and Technology, ASME, 120, pp. 287–290 (1998).CrossRefGoogle Scholar
16. Lee, K. L., Pan, W. F. and Kuo, J. N., “The Influence of the Diameter-to-Thickness Ratio on the Stability of Circular Tubes Under Cyclic Bending,” International Journal of Solids and Structures, 38, pp. 2401–2413 (2001).CrossRefGoogle Scholar
17. Lee, K. L., Pan, W. F. and Hsu, C. M., “Experimental and Theoretical Evaluations of the Effect between Diameter-to-Thickness Ratio and Curvature-Rate on the Stability of Circular Tubes Under Cyclic Bending,” JSME International Journal, Series A, 47, pp. 212–222 (2004).CrossRefGoogle Scholar
18. Chang, K. H., Pan, W. F. and Lee, K. L., “Mean Moment Effect of Thin-Walled Tubes Under Cyclic Bending,” Structural Engineering and Mechanics – an International Journal, 28, pp. 495–514 (2008).CrossRefGoogle Scholar
19. Chang, K. H. and Pan, W. F., “Buckling Life Estimation of Circular Tubes Under Cyclic Bending,” International Journal of Solids and Structures, 46, pp. 254–270 (2009).CrossRefGoogle Scholar
20. Lee, K. L., Hung, C. Y. and Pan, W. F., “Variation of Ovalization for Sharp-Notched Circular Tubes Under Cyclic Bending,” Journal of Mechanics, 26, pp. 403–411 (2010).CrossRefGoogle Scholar
21. Lee, K. L., “Mechanical Behavior and Buckling Failure of Sharp-Notched Circular Tubes Under Cyclic Bending,” Structural Engineering and Mechanics – An International Journal, 34, pp. 367–376 (2010).CrossRefGoogle Scholar
22. Hung, C. Y. and Lee, K. L., “The Influence of the Curvature-Rate on the Response and Collapse of Sharp-Notched Circular Under Cyclic Bending,” Journal of Solid Mechanics and Materials Engineering, 4, pp. 1754–1764 (2010).CrossRefGoogle Scholar