Hostname: page-component-586b7cd67f-tf8b9 Total loading time: 0 Render date: 2024-11-29T10:36:35.850Z Has data issue: false hasContentIssue false
  • English
  • Français

Continuous Microindentation of Passivated Surfaces in Surface Active Media

Published online by Cambridge University Press:  15 February 2011

Shankar K. Venkataraman ,
He Huang ,
David L. Kohlstedt  and
William .W. Gerberich
Shankar K. Venkataraman
Affiliation:
Department of Chemical Engineering and Materials Science, University of Minnesota, Minneapolis, MN 55455.
He Huang
Affiliation:
Department of Chemical Engineering and Materials Science, University of Minnesota, Minneapolis, MN 55455.
David L. Kohlstedt
Affiliation:
Department of Geology and Geophysics, University of Minnesota, Minneapolis, MN 55455.
William .W. Gerberich
Affiliation:
Department of Chemical Engineering and Materials Science, University of Minnesota, Minneapolis, MN 55455.
Get access

Abstract

Continuous microindentation tests on electropolished, single crystal Fe(3wt%Si) and Ni surfaces with thin passivation layers exhibit sharp discontinuities in the load-displacement behavior. At the discontinuity, which occurs at a load of 1.8 mN for Fe(3wt%Si) and 0.1 mN for Ni, stresses below the indenter were close to the theoretical strength of the corresponding metal. Microindentation tests performed to loads less than the discontinuity point showed an elastic load-unload behavior. On removing the passive film with a NaCl or HC1 solution, strengths are one to two orders of magnitude smaller in the presence of the chloride ions. On evaporation of the liquid, the load at the discontinuity returned to its initial value due to repassivation, indicative of a passivation oxide layer with varying thickness. This conclusion was verified by ellipsometry. Even though the elastic load-unload behavior on the passivated surface suggests elastic behavior, both elastic finite element and non-linear, elastic perfectly plastic finite element solutions strongly suggest that this might not be the case. Several suggestions as to the reasons for the deviation from continuum theory are presented.

Type
Research Article
Information
MRS Online Proceedings Library (OPL) , Volume 308: Symposium M1 – Thin Films: Stresses and Mechanical Properties IV , 1993 , 543
Copyright
Copyright © Materials Research Society 1993

Access options

Get access to the full version of this content by using one of the access options below. (Log in options will check for institutional or personal access. Content may require purchase if you do not have access.)

References

REFERENCES

1 Gane, N., Proc. Roy. Soc. Lond. A. 317, 367 (1970).Google Scholar
2 Smith, D.A. and Bowkett, K.M., Fourth European regional conference on electron microscopy, Vol. I, p. 261 (1968).Google Scholar
3 Gane, N. and Bowden, F.P., J. Appl. Phys. 39, 1432 (1968).Google Scholar
4 Venkataraman, S.K., Kohlstedt, D.L. and Gerberich, W.W., J. Mater. Res.,Google Scholar
5 Pethica, J.B. and Tabor, D., Surface Science 89, 182 (1979).CrossRefGoogle Scholar
6 Oliver, W.C. and Pharr, G.M., J.Mater. Res., 7, 1564 (1992).CrossRefGoogle Scholar
7 Timoshenko, and Goodier, , Theory of Elasticity, second edition (McGraw Hill publications, New York, 1951), pp. 93.Google Scholar
8 Johnson, K.L., Contact Mechanics (Cambridge University Press, 1985), pp. 90–93, 111–114.Google Scholar
9 Montmitonnet, P., Edlinger, M.L. and Felder, E., J. Tribology 115, 10 (1993).Google Scholar
10 Venkataraman, S.K., Kohlstedt, D.L., and Gerberich, W.W., in preparation.Google Scholar