Hostname: page-component-78c5997874-fbnjt Total loading time: 0 Render date: 2024-11-18T05:46:24.330Z Has data issue: false hasContentIssue false
  • English
  • Français

Creep-Fatigue Behavior of Microelectronic Solder Joints

Published online by Cambridge University Press:  15 February 2011

R. G. Ross Jr ,
L. C. Wen ,
G. R. Mon ,
E. Jetter  and
J. Winslow
R. G. Ross Jr
Affiliation:
Jet Propulsion Laboratory, California Institute of Technology, Pasadena, California
L. C. Wen
Affiliation:
Jet Propulsion Laboratory, California Institute of Technology, Pasadena, California
G. R. Mon
Affiliation:
Jet Propulsion Laboratory, California Institute of Technology, Pasadena, California
E. Jetter
Affiliation:
Jet Propulsion Laboratory, California Institute of Technology, Pasadena, California
J. Winslow
Affiliation:
Jet Propulsion Laboratory, California Institute of Technology, Pasadena, California
Get access

Abstract

Even at room temperature, solder joints exhibit both creep and fatigue behavior that is strongly dependent on solder joint configuration, the thermal environment, and the solder alloy properties. The microstructures of solder joints with up to 25 years of aging have been studied using SEM/EDS and metallographic techniques. Data are presented on grain growth and metallurgical composition versus aging time. A special non-linear finite element creep-fatigue simulation model has been developed, based on measured strain-rate hardness relationships, and used to analytically predict the effects of observed metallurgical changes and the effects of lead stiffness in solder joint creepfatigue interaction. To corroborate the analytical results, a special bi-metallic test fixture has been developed to accelerate the thermo-mechanical loading of solder joints in thermal cycling environments. Measured time-to-failure data for various electronicpackage lead configurations/stiffnesses, including gullwing and J-lead, are presented and shown to be in reasonable agreement with the analytical results.

Type
Research Article
Information
MRS Online Proceedings Library (OPL) , Volume 225: Symposium G – Materials Reliability Issues in Microelectronics , 1991 , 187
Copyright
Copyright © Materials Research Society 1991

Access options

Get access to the full version of this content by using one of the access options below. (Log in options will check for institutional or personal access. Content may require purchase if you do not have access.)

References

REFERENCES

1. Wild, R.N., Some Fatigue Properties of Solders and Solder Joints, IBM Report No. 7AZ000481, IBM Federal Systems Division, New York, 1975.Google Scholar
2. Avery, D.H. and Backofen, W.A., “A Structural Basis for Superplasticity,” Transactions of the ASM, v.58, 1965, pp. 551–562.Google Scholar
3. Cline, H.E. and Alder, T.H., “Rate Sensitive Deformation in Tin-Lead Alloy”, Trans. AIME, v.239, 1967, pp. 710–714.Google Scholar
4. Weinbel, R.C., Tien, J.K., Pollak, R.A., and Kang, S.K., “Creep-Fatigue Interaction in Eutectic Lead-Tin Solder Alloy”, J. of Material Science Letter, v.6, 1987, pp. 3091–3096.Google Scholar
5. Zehr, S.W. and Backofen, W.A., “Superplasticity in Lead-Tin Alloys”, Transaction of the ASM, v.61, 1968, pp. 300–312.Google Scholar
6. Murty, G.S., “Stress Relaxation in Superplastic Materials”, J. of Material Science, v.8, 1973, pp. 611–614.Google Scholar
7. Kashyap, B.P. and Murty, G.S., “Experimental Constitutive Relations for the High Temperature Deformation of a Pb-Sn Eutectic Alloy”, Materials Science and Engrg, v.50, 1981, pp. 205–213.Google Scholar