Hostname: page-component-586b7cd67f-t7fkt Total loading time: 0 Render date: 2024-11-28T10:36:30.386Z Has data issue: false hasContentIssue false
  • English
  • Français

Nanoindentation Induced Deformation Near Grain Boundaries of Corrosion Resistant Nickel Alloys

Published online by Cambridge University Press:  10 March 2011

F. William Herbert ,
Bilge Yildiz  and
Krystyn J. Van Vliet
F. William Herbert
Affiliation:
Department of Materials Science & Engineering, Massachusetts Institute of Technology, 77 Mass. Av., Cambridge, MA 02139
Bilge Yildiz
Affiliation:
Department of Nuclear Science & Engineering, Massachusetts Institute of Technology, 77 Mass. Av., Cambridge, MA 02139
Krystyn J. Van Vliet
Affiliation:
Department of Materials Science & Engineering, Massachusetts Institute of Technology, 77 Mass. Av., Cambridge, MA 02139
Get access

Abstract

The damage accumulation behavior of different grain boundary structures in Inconel 690 (Ni-29wt%Cr-9wt%Fe) was investigated in the presence of large, localized plastic strains induced by nanoindentation. Spatially-resolved hardness was measured as a function of lateral distance from ‘random’ high-angle grain boundaries and twin boundaries. The confinement of induced defects between the indenter tip and grain boundaries did not lead to significant differences in measured hardness between high angle and twin boundaries. Critical “pop-in” loads indicating the onset of incipient plasticity were lower within 1μm of grain boundaries, but were statistically equivalent for random and twin boundaries. These results suggest a comparable extent of dislocation mobility and absorption at the different grain boundary types in Inconel 690 under ambient conditions.

Keywords

grain boundariesnano-indentationhardness
Type
Research Article
Information
MRS Online Proceedings Library (OPL) , Volume 1297: Symposium P – Deformation Mechanisms, Microstructure Evolution and Mechanical Properties of Nanoscale Materials , 2011 , mrsf10-1297-p10-63
Copyright
Copyright © Materials Research Society 2011

Access options

Get access to the full version of this content by using one of the access options below. (Log in options will check for institutional or personal access. Content may require purchase if you do not have access.)

References

REFERENCES

[1] Esquivel, E.V., Murr, L.E., Materials Science & Engineering A 409 (2005)Google Scholar
[2] Ashby, M.F., Philosophical Magazine 21 (1970)Google Scholar
[3] Thaveepringsriporn, V., Was, G.S., Metall. Trans. 28A: 2101 (1997)Google Scholar
[4] Marrow, J., Engelberg, D., Jivkov, A., Wood, P., Babout, L., Stevens, N., Energy Materials 1(2) (2006)Google Scholar
[5] Randle, V., Mat. Sci. & Technology 26(3) (2010)Google Scholar
[6] Soer, W.A., Aifantis, K.E., ThM DeHosson, J., Acta Materialia 53 (2005)Google Scholar
[7] Soifer, Ya.M., Verdyan, A., Kazakevich, M., Rabkin, E., Scripta Materialia 47 (2002)Google Scholar
[8] Ohmura, T., Tsuzaki, K., J. Phys. D: Appl. Phys 41 (2008)Google Scholar
[9] Wo, P.C., Ngan, A.H.W., J. Materials Research Society 19(1) (2004)Google Scholar
[10] Fisher-Cripps, A.C., Nanoindentation, Springer 2nd Ed. (2004)Google Scholar
[11] Petch, N.J., J. of the Iron & Steel Institute 6(1) (1953)Google Scholar
[12] Esquivel, E.V., Murr, L.E., Materials Science & Engineering A 409 (2005)Google Scholar