Hostname: page-component-78c5997874-xbtfd Total loading time: 0 Render date: 2024-11-09T03:34:43.227Z Has data issue: false hasContentIssue false
  • English
  • Français

Nanoindentation of Ion Implanted and Deposited Amorphous Silicon

Published online by Cambridge University Press:  01 February 2011

J. S. Williams ,
B. Haberl  and
J. E. Bradby
J. S. Williams
Affiliation:
Department of Electronic Materials Engineering, Research School of Physical Sciences and Engineering, The Australian National University, Canberra, ACT 0200, Australia
B. Haberl
Affiliation:
Department of Electronic Materials Engineering, Research School of Physical Sciences and Engineering, The Australian National University, Canberra, ACT 0200, Australia
J. E. Bradby
Affiliation:
Department of Electronic Materials Engineering, Research School of Physical Sciences and Engineering, The Australian National University, Canberra, ACT 0200, Australia
Get access

Abstract

The deformation behavior of both ion-implanted and deposited amorphous Si (a-Si) films has been studied using spherical nanoindentation, followed by analysis using Raman spectroscopy and cross-sectional transmission electron microscopy (XTEM). Indentation was carried out on both unannealed a-Si films (the so-called unrelaxed state) and in ion implanted films that were annealed to 450°C to fully relax the amorphous film. The dominant mode of deformation in unrelaxed films was via plastic flow of the amorphous phase rather than phase transformation, with measured hardness being typically 75–85% of that of crystalline Si. In contrast, deformation via phase transformation was clearly observed in the relaxed state of ion implanted a-Si, with the load-unload curves displaying characteristic discontinuities and Raman and XTEM indicating the presence of high-pressure crystalline phases Si-III and Si-XII following pressure release. In such cases the measured hardness was within 5% of that of the crystalline phase.

Type
Research Article
Information
MRS Online Proceedings Library (OPL) , Volume 843: Symposium T – Surface Engineering-Fundamentals and Applications , 2004 , T6.3/R10.3
Copyright
Copyright © Materials Research Society 2005

Access options

Get access to the full version of this content by using one of the access options below. (Log in options will check for institutional or personal access. Content may require purchase if you do not have access.)

References

REFERENCES

1. Hu, J. Z., Merkle, L. D., Menoni, C. S., and Spain, I. L., Phys. Rev. B 34, 4679 (1986).Google Scholar
2. Clarke, D. R., Kroll, M. C., Kirchner, P. D., Cook, R. F., and Hockey, B. J., Phys. Rev. Lett. 60, 2156 (1988).Google Scholar
3. Domnich, V., Gogotsi, Y., and Dub, S., Appl. Phys. Lett. 76, 2214 (2000).Google Scholar
4. Bradby, J. E., Williams, J. S., Wong-Leung, J., Swain, M. V., and Munroe, P., Appl. Phys. Lett. 77, 3749 (2000).Google Scholar
5. Bradby, J. E., Williams, J. S., Wong-Leung, J., Swain, M. V., and Munroe, P., J. Mater. Res. 16, 1500 (2001).Google Scholar
6. Williams, J. S., Field, J. S., and Swain, M. V., Mater. Res. Soc. Symp. Proc. 308, 571 (1993).Google Scholar
7. Roorda, S., Sinke, W. C., Potae, J. M., Jacobson, D.C., Dieker, S., Dennis, B. S., Eaglesham, D. J., Spaepen, F., and Fuoss, P., Phys. Rev. B 44, 3702 (1991).Google Scholar
8. Follstaedt, D. M., Knapp, J. A., and Myers, S. M., J. Mater. Res. 19, 338 (2004).Google Scholar
9. Haberl, B., Bradby, J. E., Swain, M.V., Williams, J. S., and Munroe, P., Appl. Phys. Lett. 85, 5559 (2004).Google Scholar
10. Roorda, S., Doorn, S., Sinke, W. C., Scholte, P. M. L. O., and van Loenen, E., Phys. Rev. Lett. 62, 1880 (1989).Google Scholar
11. Gogotsi, Y. G., Domnich, V., Dub, S. N., Kailer, A., and Nickel, K. G., J. Mater. Res. 15, 871 (2000).Google Scholar