Hostname: page-component-586b7cd67f-dsjbd Total loading time: 0 Render date: 2024-11-25T17:26:42.802Z Has data issue: false hasContentIssue false
  • English
  • Français

Preparation of Triple-Junction A-Si:H NIP Based Solar Cells at Deposition Rates of 10 Å/s using a Very High Frequency Technique

Published online by Cambridge University Press:  15 February 2011

S.J. Jones ,
X. Deng ,
T. Liu  and
M. Izu
S.J. Jones
Affiliation:
Energy Conversion Devices, Inc., Troy, MI 48084
X. Deng
Affiliation:
Energy Conversion Devices, Inc., Troy, MI 48084
T. Liu
Affiliation:
Energy Conversion Devices, Inc., Troy, MI 48084
M. Izu
Affiliation:
Energy Conversion Devices, Inc., Troy, MI 48084
Get access

Abstract

In an effort to find an alternative deposition method to the standard low deposition rate 13.56 M-z PECVD technique, the feasibility of using a 70 MiHz rf plasma frequency to prepare a-Si:H based i-layer materials at high rates for nip based triple-junction solar cells has been tested. As a prelude to multi-junction cell fabrication, the deposition conditions used to make single-junction a-Si:H and a-SiGe:H cells using this Very High Frequency (VHF) method have been varied to optimize the material quality and the cell efficiencies. It was found that the efficiencies and the light stability for both a-Si:H and a-SiGe:H single-junction cells remain relatively constant as the i-layer deposition rate is varied from 1 to 10 Å/s. Also these stable efficiencies are similar to those for cells made at low deposition rates (1 Å/s) using the standard 13.56 MHz PECVD technique and the same deposition equipment. Using the knowledge obtained in the fabrication of the single-junction devices, a-Si:H/a-SiGe:H/a-SiGe:H triple-junction solar cells have been fabricated with all of the i-layers prepared using the VHF technique and deposition rates near 10 Å/s. Thin doped layers for these devices were prepared using the standard 13.56 MIHz rf frequency and deposition rates near 1 Å/s. Pre-light soaked efficiencies of greater than 10% have been obtained for these cells prepared at the high rates. In addition, after 600 hrs. of light soaking under white light conditions, the cell efficiencies degraded by only 10-13%, values similar to the degree of degradation for high efficiency triple-junction cells made by the standard 13.56 MiHz method using i-layer deposition rates near 1 Å/s. Thus, use of this VHF method in the production of large area a-Si:H based multi-junction solar modules will allow for higher i-layer deposition rates, higher module throughput and reduced module cost.

Type
Research Article
Information
MRS Online Proceedings Library (OPL) , Volume 557: Symposium A – Amorphous and Heterogeneous Silicon Thin Films—Fundamentals to Devices—1999 , 1999 , 133
Copyright
Copyright © Materials Research Society 1999

Access options

Get access to the full version of this content by using one of the access options below. (Log in options will check for institutional or personal access. Content may require purchase if you do not have access.)

References

1. Chatam, H. and Bhat, PK., Mat. Res. Soc. Proc. 149, 447 (1989).Google Scholar
2. Shah, A., Dutta, J., Wyrsch, N., Prasad, K., Curtins, H., Finger, F., Howling, A., and Hollenstein, Ch., Mat. Res. Soc. Proc. 258, 15 (1992).Google Scholar
3. Jones, S.J., Deng, X., Liu, T., and Izu, M., Mat. Res. Soc. Proc. 507, 113 (1998).Google Scholar
4. Yang, J., Sugiyama, S., Guha, S., Mat. Res. Soc. Proc. 507, 157 (1998).Google Scholar
5. Izu, M., Deng, X., Krisko, A., Whelan, K., Young, R., Ovshinsky, H.C., Narasimhan, K.L. and Ovshinsky, S.R., Proc. 23rd IEEE PV Spec. Conf., p. 919 (1993).Google Scholar
6. Sansonnens, L., Howling, A.A., Ch. Hollenstein, Mat. Res. Soc. Proc. 507, 541 (1998).Google Scholar