Hostname: page-component-586b7cd67f-r5fsc Total loading time: 0 Render date: 2024-11-25T19:41:06.308Z Has data issue: false hasContentIssue false
  • English
  • Français

Soft and Hard Modes of Deformation in Mosi2 Single Crystals

Published online by Cambridge University Press:  22 February 2011

K. Ito ,
T. Yano ,
H. Inui  and
M. Yamaguchi
K. Ito
Affiliation:
Department of Materials Science and Engineering, Kyoto University, Sakyo-ku, Kyoto 606–01, Japan.
T. Yano
Affiliation:
Department of Materials Science and Engineering, Kyoto University, Sakyo-ku, Kyoto 606–01, Japan.
H. Inui
Affiliation:
Department of Materials Science and Engineering, Kyoto University, Sakyo-ku, Kyoto 606–01, Japan.
M. Yamaguchi
Affiliation:
Department of Materials Science and Engineering, Kyoto University, Sakyo-ku, Kyoto 606–01, Japan.
Get access

Abstract

The deformation behavior of MoSi2 single crystals has been studied in the temperature range of -196<1500°C. While [001]-oriented crystals can be plastically deformed only above 1300°C, plastic flow is possible from temperatures as low as room temperature for single crystals with orientations other than [001]. Five slip systems, {110)<111], {011)<100], {010)<100], {023)<100] and {013)<331], are identified to be operative, depending on crystal orientation. An anomalous increase in CRSS is observed in the intermediate temperature range for the former three slip systems. Schmid’s law is generally valid for the soft modes, {110)<111], {011)<100] and {023)<100]. In contrast, the CRSS for the hard mode, {013)<331], strongly depends on crystal orientation with the higher values for orientations closer to [001].

Type
Research Article
Information
MRS Online Proceedings Library (OPL) , Volume 364: Symposium L – High-Temperature Ordered Intermetallic Alloys–VI , 1994 , 899
Copyright
Copyright © Materials Research Society 1995

Access options

Get access to the full version of this content by using one of the access options below. (Log in options will check for institutional or personal access. Content may require purchase if you do not have access.)

References

1. Mcschter, P.J. and Schwartz, D.S., JOM, Nov., 52 (1989).Google Scholar
2. Petrovic, J.J. and Vasudevan, A.K., in Intermetallic Matrix Composites II. edited by Miracle, D.B., Anton, D.L. and Graves, J.A. (Mater. Res. Soc. Proc. 273, Pittsburgh, PA, 1992), pp. 229–239.Google Scholar
3. Vasudevan, A.K. and Petrovic, J.J., Mater. Sci. Eng. A, 155, 1 (1992).Google Scholar
4. Boettinger, W.J., Perepezko, J.H. and Frankwicz, P.S., Mater. Sci. Eng. A, 155, 33 (1992).Google Scholar
5. Umakoshi, Y., Sakagami, T., Hirano, T. and Yamane, T., Acta metall. mater., 38, 909 (1990).Google Scholar
6. Kimura, K., Nakamura, M. and Hirano, T., J. Mater. Sci., 25, 2487 (1990).Google Scholar
7. Mitchell, T.E. and Maloy, S.A., in Critical Issues in the Development of High Temperature Structural Materials, edited by Stoloff, N.S., Duquette, D.J. and Giamei, A.F. (The Minerals, Metals & Materials Society, Warrendalc, PA, 1993), p. 279.Google Scholar
8. Maloy, S.A., Mitchell, T.E., Petrovic, J.J., Heuer, A.H. and Lewandowski, J.J., in High Temperature Silicides and Refractory Alloys, edited by Briant, C.L., Petrovic, J.J., Bewlay, B.P., Vasudevan, A.K. and Lipsitt, H.A. (Mater. Res. Soc. Proc. 322, Pittsburgh, PA, 1994), pp. 21–26.Google Scholar
9. Paidar, V., Pope, D.P. and Vitek, V., Acta metall., 32, 435 (1984).Google Scholar
10. Rao, S.I., Dimiduk, D.M. and Mendiratta, M.G., Phil. Mag. A, 68, 1295 (1993).Google Scholar
11. Ito, K., Inui, H. and Yamaguchi, M., Phil. Mag. A, submitted (1994).Google Scholar
12. Hirsch, P.B., Phil. Mag. A, 65, 569 (1992).Google Scholar
13. Friedel, J., in Dislocations (Pergamon, Oxford,1964), p.411.Google Scholar