Hostname: page-component-586b7cd67f-rdxmf Total loading time: 0 Render date: 2024-11-29T11:51:46.103Z Has data issue: false hasContentIssue false
  • English
  • Français

Tribological Applications for Advanced Ceramics

Published online by Cambridge University Press:  28 February 2011

S. Jahanmir
S. Jahanmir*
Affiliation:
Ceramics Division, National Institute of Standards and Technology, Gaithersburg, MD 20899
Get access

Abstract

Advanced structural ceramics offer unique capabilities as tribomaterials. They are being used today in diverse applications such as tips for ball-point pens, precision instrumentbearings, and cutting tool inserts. Tribological applications of ceramics can be divided into several categories based on the properties of the ceramics. These include: resistance to abrasion and erosion; resistance to corrosive wear; wear resistance at elevated temperatures; low density; and electrical, thermal and magnetic properties. Examples of present utilization of ceramics in each category are described and a few examples of potentialfuture applications are given. Many scientific and technical barriers must be overcome before the full potential of ceramics in tribological applications is realized. These barriers are discussed in terms of the limited knowledge regarding tribological performance, problems with reliability, and lack of design knowledge and experience. It is clear that the wide-spread use of advanced ceramics requires further research and development. However, it must be realized that the solutions to the scientific and technical problems will be slow.

Type
Research Article
Information
MRS Online Proceedings Library (OPL) , Volume 140: Symposium S – New Materials Approaches to Tribology: Theory and Applications , 1988 , 285
Copyright
Copyright © Materials Research Society 1989

Access options

Get access to the full version of this content by using one of the access options below. (Log in options will check for institutional or personal access. Content may require purchase if you do not have access.)

References

1. Kingery, W.D., Bowen, H.K. and Uhlmann, D.R., Introduction of Ceramics, Second Edition, Wiley, New York, NY, 1976.Google Scholar
2. Richerson, D.W., Modern Ceramic Engineering, Dekker, New York, NY, 1982.Google Scholar
3. Ceramic Source '89, American Ceramic Society, Westerville, OH, 1989.Google Scholar
4. Clark, D.E. (ed.), Ceramic Engineering and Science Proceedings, American Ceramic Society, Westerville, OH, 1988.Google Scholar
5. “Advanced Ceramics,” Bulletin, Ceramic, Vol. 67, No. 2, pp. 341–402, 1988.Google Scholar
6. Jahanmir, S. (ed.), Tribology of Ceramics, Vol. 1 Fundamentals, Special Publication SP-23, Society of Tribologists and Lubrication Engineers, Park Ridge, IL, 1987.Google Scholar
7. Jahanmir, S. (ed.), Tribology of Ceramics, Vol. 2 Applications, Special Publication SP-24, Society of Tribologists and Lubrication Engineers, Park Ridge, IL, 1987.Google Scholar
8. Ceramic Tribological Materials, (Jan 70-Jan 88) Citations from the U.S. Patent Bibliographic Database, PB88-85238, U.S. Dept. of Commerce, NTIS, Springfield, VA, 1988.Google Scholar
9. Ceramic Bearings, Citations from the International Aerospace Abstracts Database, PB88-854708, U.S. Dept. of Commerce, NTIS, Springfield, VA, 1987.Google Scholar
10. “Machining Issue,” Ceramic Bulletin, Vol. 67, No. 6, pp. 991–1052, 1988.Google Scholar
11. Larsen, R.P. and Vyas, A.D., “The Outlook for Ceramics in Heat Engines, 1900-2010,” SAE Paper No. 880514.Google Scholar
12. Zaretsky, E.V., “Ceramic Bearings for Use in Gas Turbine Engines,” ASME Paper No. 88-GT-138.Google Scholar
13. Katz, R.N. and Hannoosh, J.G., “Ceramics for High Performance Rolling Element Bearings: A Review and Assessment,” Int. J. High Tech. Ceramics, Vol. 1, pp. 69–79, 1985.CrossRefGoogle Scholar
14. Dill, J.F., “Rolling Element Bearing Technology: Sizing up the Japanese,” Mechanical Engineering, pp. 37–40, December 1987.Google Scholar
15. Davidson, J.A. and Schwartz, G., “Wear, Creep and Frictional Heat of Femoral Implant Articulating Surfaces,” J. Biomedical Mat. Res., Vol. 21, No. A3, pp. 261–285, 1987.Google ScholarPubMed
16. Tribology of Ceramics, National Materials Advisory Board, National Research Council, NMAB-435, National Academy Press, Washington, DC, 1988.Google Scholar
17. Gates, R.S., J.P. Yellets, Deckman, D.E. and Hsu, S.M., “Considerations in Ceramic Friction and Wear Measurements,” Selection and Use of Wear Tests for Ceramics, ASTM STP 1010, Yust, C.S. and Bayer, R.G., Eds., American Society for Testing and Materials, Philadelphia, PA, pp. 1–23, 1988.CrossRefGoogle Scholar
18. Deckman, D.E., Jahanmir, S., Hsu, S.M. and Gates, R.S., “Friction and Wear Measurements for New Materials and Lubricants,” Engineering Materials for Advanced Friction and Wear Applications, Smidt, F.A. and Blau, P.J., Eds., ASM International, Metals Park, NJ, pp. 167–168, 1988.Google Scholar
19. Fischer, T.E. and Tomizawa, H., “Interaction of Tribochemistry and Microfracture in the Friction and Wear of Silicon Nitride,” Wear, Vol. 105, pp. 29–45, 1985.Google Scholar
20. Jahanmir, S. and Fischer, T.E., “Friction and Wear of Silicon Nitride Lubricated by Humid Air, Water, Hexadecane, and Hexadecane +0.5 Percent Stearic Acid,” ASLE Trans., 1988.CrossRefGoogle Scholar
21. Fischer, T.E., Anderson, M.P., Jahanmir, S. and Salher, R., “Friction and Wear of Tough and Brittle Zirconia in Nitrogen, Air, Water Hexadecane and Hexadecane Containing Stearic Acid,” Wear, Vol. 124, pp. 133–148, 1988.Google Scholar
22. Fischer, T.E., Anderson, M.P. and Jahanmir, S., “Influence of Fracture Toughness on the Wear Resistance of Yittria Doped Zirconium Oxide,” Amer, J., Ceramic Society, to be published, 1989.Google Scholar
23. Cranmer, D.C., “Ceramic Tribology - Needs and Opportunities,” Tribology Trans., Vol. 31, pp. 164–173, 1988.Google Scholar
24. Tomizawa, H. and Fischer, T.E., “Friction and Wear of Silicon Nitride at 150°C to 800°C,” ASLE Trans., Vol. 29, pp. 481–488, 1986.Google Scholar
25. Tomizawa, H. and Fischer, T.E., “Friction and Wear of Silicon Nitride and Silicon Carbide in Water,” ASLE Trans., Vol. 30, pp. 41–46, 1987.Google Scholar
26. Cho, S.J., Hockey, B.J., Lawn, B.R. and Bennison, S.J., “Grain Size and R-Curve Effects in the Abrasive Wear of Alumina,” to be published in Amer, J., Ceramic Society (Communications), 1989.CrossRefGoogle Scholar
27. Cranmer, D.C. and Galuska, A.A., “Quantitative Wear Surface Analysis of SiC Using a Multiple-Technique Approach,” Advanced Ceramic Materials, Vol. 1, No. 3, pp. 247–251, 1986.CrossRefGoogle Scholar
28. Hegemann, B.E., Jahanmir, S. and Hsu, S.M., “Microspectroscopy Applications in Tribology,” Microbeam Analysis, Newbury, D.E., Ed., San Francisco Press, San Francisco, CA, pp. 193–196, 1988.Google Scholar