Hostname: page-component-78c5997874-ndw9j Total loading time: 0 Render date: 2024-11-19T12:08:50.932Z Has data issue: false hasContentIssue false
  • English
  • Français

A comparative microtribological investigation of diamond-like carbon films for applications in microsystems

Published online by Cambridge University Press:  11 February 2011

S. Imad-Uddin Ahmed ,
Giuseppe Bregliozzi  and
Henry Haefke
S. Imad-Uddin Ahmed
Affiliation:
CSEM Swiss Center for Electronics and Microtechnology Inc., Rue Jaquet Droz 1, CH-2007 Neuchâtel, Switzerland
Giuseppe Bregliozzi
Affiliation:
CSEM Swiss Center for Electronics and Microtechnology Inc., Rue Jaquet Droz 1, CH-2007 Neuchâtel, Switzerland
Henry Haefke
Affiliation:
CSEM Swiss Center for Electronics and Microtechnology Inc., Rue Jaquet Droz 1, CH-2007 Neuchâtel, Switzerland
Get access

Abstract

This study reports on the microfrictional properties under reciprocating sliding of different types of commercially available diamond-like carbon (DLC) films, prepared using low and high frequency plasma-assisted chemical vapor deposition (PACVD) and the vacuum arc method. Silicon and sapphire balls were used as counterbodies. Friction-load curves suggest that, for applied forces in the N to μN regime, two properties have a strong influence on the microfriction: First, the chemical composition plays a dominant role and second, the film roughness. With silicon against DLC, microfriction of hydrogen-free DLC films was greater than the hydrogen containing films. With sapphire counterbodies, microfriction was inversely proportional to film roughness. For all films tested, microfriction was independent of the sliding velocity. Mild wear in the form of scratches was observed only on silicon, while no wear could be detected on any of the DLC films. These results illustrate the utility of implementing microtribological testing in a coating development for microsystems.

Type
Research Article
Information
MRS Online Proceedings Library (OPL) , Volume 750: Symposium Y – Surface Engineering 2002–Synthesis, Characterization and Applications , 2002 , Y7.2/Y13.2
Copyright
Copyright © Materials Research Society 2003

Access options

Get access to the full version of this content by using one of the access options below. (Log in options will check for institutional or personal access. Content may require purchase if you do not have access.)

References

REFERENCES

1. Holmberg, K. and Matthews, A., Coatings Tribology, Tribology Series, 28, (Elsevier, 1994), p. 213.Google Scholar
2. Grill, A., Surf. Coat Technol., 94–95, 507 (1997).Google Scholar
3. Matthews, A., Eskildsen, S.S., Diam. Rel. Mater. 3, 902(1994).Google Scholar
4. Maboudian, R., Surf. Sci. Rep. 30, 207 (1998).Google Scholar
5. Grill, A., Wear 168, 143 (1993).Google Scholar
6. Liu, H., Ahmed, S.I.-U., Scherge, M., Thin Solid Films 381, 135 (2001).Google Scholar
7. Gerbig, Y., Vercammen, K., Meneve, J., Haefke, H., Proc. of the GfT-Tribologie-Fachtagung “Reibung, Schmierung und Verschleiss”, Göttingen, Germany, 2000, pp. 27/1–9.Google Scholar
8. Meneve, J., Havermans, D., Vercammen, K., Haefke, H., Gerbig, Y., Pflüger, E., Adv. Eng. Mat. 3, 163 (2001).Google Scholar
9. Vercammen, K., Haefke, H., Gerbig, Y., Van Hulsel, A., Pflüger, E., Meneve, J., Surf. Coat. Technol. 133–134, 466 (2000).Google Scholar
10. Scherge, M., Ahmed, S.I., Mollenhauer, O., Spiller, F., Technisches Messen, 67, 324 (2000).Google Scholar
11. Scherge, M., Gorb, S. N., Biological Micro- and Nanotribology, NanoScience and Technology, (Springer-Verlag, 2001).Google Scholar
12. Scherge, M., Li, X., Schaefer, J.A., Tribol. Lett. 6, 215–220 (1999).Google Scholar
13. Butter, R.S., Waterman, D.R., Lettington, A.H., Ramos, R.T., Fordham, E.J., Thin Solid Films 311, 107 (1997).Google Scholar
14. Erdemir, A., Nilufer, I.B., Eryilmaz, O.L., Beschliesser, M., Fenske, G.R., Surf. Coat. Technol. 120–121, 589 (1999).Google Scholar
15. Ronkainen, H., Koskinen, J., Likonen, J., Varjus, S. and Vihersalo, J., Diam. Rel. Mater. 3, 1329 (1994).Google Scholar
16. Ronkainen, H., Varjus, S., Holmberg, K., Wear 222, 120 (1998).Google Scholar
17. Nevshupa, R.A., Scherge, M., Ahmed, S.I.-U., Surf. Sci. 517, 17 (2002).Google Scholar
18. Riedo, E., Lévy, F., Brune, H., Phy. Rev. Lett. 88, 185505–1/4 (2002).Google Scholar
19. Ahmed, S.I-U., Scherge, M., Opitz, A., Schaefer, J.A., to be published.Google Scholar