The development of exoskeletons is currently a lengthy process full of challenges. We are proposing a framework to accelerate the process and make the resulting exoskeletons more user-centered. The needed accomplishments in science are described in an effort to lay the foundation for future research projects. Since the early 2000s, exoskeletons have been discussed as an emerging technology in industrial, medical, or military applications. Those systems are designed to support people during manual tasks. At first, those systems lacked broad acceptance. Many models found their niches in ongoing developments and more diverse systems entering the market. There are still applications that are in dire need of such assistance. Due to the lack of experience with body-worn robotics, the development of such systems has been shaped by trial and error. The lack of legacy products results in longer development times. In this paper, a process to generate a framework is presented to display the required research to enable future exoskeleton designers. Owing to their proximity to the user’s body, exoskeletons are highly complex systems that need sophisticated subsystems, such as kinematic, control, interaction design, or actuators, to be accepted by users. Due to the wide variety of fields and high user demands, a synchronized multidisciplinary effort is necessary. To achieve this, a process to develop a modular framework for exoskeleton design is proposed. It focuses on user- and use-case-centered solutions for matching kinematics, actuation, and control. To ensure the usefulness of the framework, an evaluation of the incorporated solutions is required.

Cumulative back muscle fatigue plays a role in the occurrence of low-back injuries in occupations that require repetitive lifting of heavy loads and working in forward leaning postures. Lift-support exoskeletons have the potential to reduce back and hip muscle activity, thereby delaying the onset of fatigue in these muscles. Therefore, exoskeletons are being considered a potentially important tool to further reduce workload-related injuries. However, today no standards have been established on how to benchmark the support level of lift-support exoskeletons. This work proposes an experimental protocol to quantify the support level of a lift-support exoskeletons on instant changes in muscle activity and fatigue development while maintaining a static forward leaning posture. It then applies the protocol to experimentally assess the effect of the support provided by a commercially available lift-support exoskeleton, the LiftSuit 2.0 (Auxivo AG, Schwerzenbach, Switzerland), on the user. In a sample of 14 participants, the amplitude of the muscle activity of the back muscles \left({\Delta}_{\mathrm{erectorspinae},\mathrm{thoracic}}\hskip0.35em =\hskip0.35em 33.0\%,{\Delta}_{\mathrm{erectorspinae},\mathrm{lumbar}}\hskip0.35em =\hskip0.35em 13.2\%\right) $\left({\Delta}_{\mathrm{erectorspinae},\mathrm{thoracic}}\hskip0.35em =\hskip0.35em 33.0\%,{\Delta}_{\mathrm{erectorspinae},\mathrm{lumbar}}\hskip0.35em =\hskip0.35em 13.2\%\right)$ and hip muscles ( {\Delta}_{\mathrm{gluteusmaximus}}\hskip0.35em =\hskip0.35em 16.3\% ${\Delta}_{\mathrm{gluteusmaximus}}\hskip0.35em =\hskip0.35em 16.3\%$ ) was significantly reduced. Wearing the exoskeleton significantly reduced the amount of fatigue developed during the task ( {\Delta}_{\mathrm{quadratuslumborum}}\hskip0.35em =\hskip0.35em 10.1\%,{\Delta}_{\mathrm{gluteusmaximus}}\hskip0.35em =\hskip0.35em 44.0\% ${\Delta}_{\mathrm{quadratuslumborum}}\hskip0.35em =\hskip0.35em 10.1\%,{\Delta}_{\mathrm{gluteusmaximus}}\hskip0.35em =\hskip0.35em 44.0\%$ ). Changes in muscle fatigue can be objectively recorded and correlated with relevant changes for exoskeleton users: the time a task can be performed and perceived low-back fatigue. Thus, including such measures of fatigue in standardized benchmarking procedures will help quantify the benefits of exoskeletons for occupational use.

Wearable robotic devices (WRD) are still struggling to fulfill their vast potential. Inadequate daily life usability is one of the main hindrances to increased technology acceptance. Improving usability evaluation practices during the development of WRD could help address these limitations. In this work, we present the design and validation of a novel online platform aiming to fill this gap, the Interactive Usability Toolbox (IUT). This platform consists of a public website that offers an interactive, context-specific search within a database of 154 user research methods and educational information about usability. In a dedicated study, the effect of this platform to support usability evaluation was investigated. Twelve WRD experts were asked to complete the task of defining usability evaluation protocols for two specific use cases. The platform was provided to support one of the use cases. The quality and composition of the proposed protocols were assessed by (i) two blinded reviewers, (ii) the participants themselves, and (iii) the study coordinators. We showed that using the IUT significantly affected the proposed evaluation focus, shifting protocols from mainly effectiveness-oriented to more user-focused studies. The protocol quality, as rated by the external reviewers, remained equivalent to those designed with conventional strategies. A mixed-method usability evaluation of the platform yielded an overall positive image, with detailed suggestions for further improvements. The IUT is expected to positively affect the evaluation and development of WRD through its educational value, the context-specific recommendations supporting ongoing benchmarking endeavors, and highlighting the value of qualitative user research.

The development of wearable technology, which enables motion tracking analysis for human movement outside the laboratory, can improve awareness of personal health and performance. This study used a wearable smart sock prototype to track foot–ankle kinematics during gait movement. Multivariable linear regression and two deep learning models, including long short-term memory (LSTM) and convolutional neural networks, were trained to estimate the joint angles in sagittal and frontal planes measured by an optical motion capture system. Participant-specific models were established for ten healthy subjects walking on a treadmill. The prototype was tested at various walking speeds to assess its ability to track movements for multiple speeds and generalize models for estimating joint angles in sagittal and frontal planes. LSTM outperformed other models with lower mean absolute error (MAE), lower root mean squared error, and higher R-squared values. The average MAE score was less than 1.138° and 0.939° in sagittal and frontal planes, respectively, when training models for each speed and 2.15° and 1.14° when trained and evaluated for all speeds. These results indicate wearable smart socks to generalize foot–ankle kinematics over various walking speeds with relatively low error and could consequently be used to measure gait parameters without the need for a lab-constricted motion capture system.

The treatment and evacuation of people with lower limb fractures in austere environments presents unique challenges that assistive exoskeletal devices could address. In these dangerous situations, independent mobility for the injured can preserve their vital capabilities so that they can safely evacuate and minimize the need for additional personnel to help. This expert view article discusses how different exoskeleton archetypes could provide independent mobility while satisfying the requisite needs for portability, maintainability, durability, and adaptability to be available and useful within austere environments. The authors also discuss areas of development that would enable exoskeletons to operate more effectively in these scenarios as well as preserve the health of the injured limb so that definitive treatment after evacuation will produce better outcomes.

B-mode ultrasound (US) is often used to noninvasively measure skeletal muscle architecture, which contains human intent information. Extracted features from B-mode images can help improve closed-loop human–robotic interaction control when using rehabilitation/assistive devices. The traditional manual approach to inferring the muscle structural features from US images is laborious, time-consuming, and subjective among different investigators. This paper proposes a clustering-based detection method that can mimic a well-trained human expert in identifying fascicle and aponeurosis and, therefore, compute the pennation angle. The clustering-based architecture assumes that muscle fibers have tubular characteristics. It is robust for low-frequency image streams. We compared the proposed algorithm to two mature benchmark techniques: UltraTrack and ImageJ. The performance of the proposed approach showed higher accuracy in our dataset (frame frequency is 20 Hz), that is, similar to the human expert. The proposed method shows promising potential in automatic muscle fascicle orientation detection to facilitate implementations in biomechanics modeling, rehabilitation robot control design, and neuromuscular disease diagnosis with low-frequency data stream.

Shoulder exoskeletons (SEs) can assist the shoulder joint of workers during overhead work and are usually passive for good portability. However, current passive SEs face the challenge that their torque generators are often attached to the human arm, which adds a significant amount of weight to the user’s arms, resulting in additional energy consumption of the user. In this paper, we present a novel passive SE whose torque generator is attached to the user’s back and assists the shoulder joint through Bowden cables. Our approach greatly reduces the weight on the user’s arms and can accommodate complex shoulder joint movements with simple and lightweight mechanical structure based on Bowden cables. In addition, to match the nonlinear torque requirements of the shoulder joint, a unique spring-cam mechanism is proposed as the torque generator. To verify the effectiveness of the device, we conducted a usability test based on muscle activations of 10 healthy subjects. When assisting overhead work, the SE significantly reduced the mean and maximum electromyography signals of the shoulder-related muscles by up to 25%. The proposed SE contributes to further research on passive SE design to improve usability, especially in terms of reducing weight on human arms.

This study presents a new wearable insole pressure sensor (IPS), composed of fabric coated in a carbon nanotube-based composite thin film, and validates its use for quantifying ground reaction forces (GRFs) during human walking. Healthy young adults (n = 7) walked on a treadmill at three different speeds while data were recorded simultaneously from the IPS and a force plate (FP). The IPS was compared against the FP by evaluating differences between the two instruments under two different assessments: (1) comparing the two peak forces at weight acceptance and push-off (2PK) and (2) comparing the absolute maximum (MAX) of each gait cycle. Agreement between the two systems was evaluated using the Bland–Altman method. For the 2PK assessment, the group mean of differences (MoD) was −1.3 ± 4.3% body weight (BW) and the distance between the MoD and the limits of agreement (2S) was 25.4 ± 11.1% BW. For the MAX assessment, the average MoD across subjects was 1.9 ± 3.0% BW, and 2S was 15.8 ± 9.3% BW. The results of this study show that this sensor technology can be used to obtain accurate measurements of peak walking forces with a basic calibration and consequently open new opportunities to monitor GRF outside of the laboratory.

This article proposes, describes, and tests a swing-assist walking controller for a stance-controlled, swing-assisted knee prosthesis that aims to combine benefits of passive swing mechanics (e.g., quiet operation, biomimetic function, and low power requirements) with benefits of powered swing assistance (e.g., increased robustness of swing-phase motion and specifically increased toe clearance). A three-participant, multislope, multispeed treadmill walking study was performed using the swing-assist prosthesis and controller, as well as using the participants’ prescribed microprocessor knee devices. The swing-assist device and approach were found to improve user minimum foot clearance during walking at slopes and speeds, and also to improve symmetry of knee motion. Hip power inputs from stance knee release to heel strike indicated that, on average, less hip power was required when using the swing-assist prosthesis, indicating that the observed benefits were likely the result of the knee device and its control methodology, rather than a result of increased hip joint effort.

This manuscript presents a simplified dynamic human-prosthesis model and simulation framework for the purpose of designing and developing lower limb prosthesis hardware and controllers. The objective was to provide an offline design tool to verify the closed-loop behavior of the prosthesis with the human, in order to avoid relying solely on limiting kinematic and kinetic reference trajectories of (able-bodied) subjects and associated static or inverse dynamic analyses, while not having to resort to complete neuromusculoskeletal models of the human that require extensive optimizations to run. The presented approach employs a reduced-order model that includes only the prosthetic limb and trunk in a multi-body dynamic model. External forces are applied to the trunk during stance phase of the intact leg to represent its presence. Walking is realized by employing the well-known spring-loaded inverted pendulum model, which is shown to generate realistic dynamics on the prosthesis while maintaining a stable and modifiable gait. This simple approach is inspired from the rationale that the human is adaptive, and from the desire to facilitate modifications or inclusions of additional user actions. The presented framework is validated with two use cases, featuring a commercial and research knee prosthesis in combination with a passive ankle prosthesis, performing a continuous sequence of standing still, walking at different velocities and stopping.

Current laboratory-based setups (optical marker cameras + force plates) for human motion measurement require participants to stay in a constrained capture region which forbids rich movement types. This study established a fully wearable system, based on commercially available sensors (inertial measurement units + pressure insoles), that can measure both kinematic and kinetic motion data simultaneously and support wireless frame-by-frame streaming. In addition, its capability and accuracy were tested against a conventional laboratory-based setup. An experiment was conducted, with 9 participants wearing the wearable measurement system and performing 13 daily motion activities, from slow walking to fast running, together with vertical jump, squat, lunge, and single-leg landing, inside the capture space of the laboratory-based motion capture system. The recorded sensor data were post-processed to obtain joint angles, ground reaction forces (GRFs), and joint torques (via multi-body inverse dynamics). Compared to the laboratory-based system, the established wearable measurement system can measure accurate information of all lower limb joint angles (Pearson’s r = 0.929), vertical GRFs (Pearson’s r = 0.954), and ankle joint torques (Pearson’s r = 0.917). Center of pressure (CoP) in the anterior–posterior direction and knee joint torques were fairly matched (Pearson’s r = 0.683 and 0.612, respectively). Calculated hip joint torques and measured medial–lateral CoP did not match with the laboratory-based system (Pearson’s r = 0.21 and 0.47, respectively). Furthermore, both raw and processed datasets are openly accessible (https://doi.org/10.5281/zenodo.6457662). Documentation, data processing codes, and guidelines to establish the real-time wearable kinetic measurement system are also shared (https://github.com/HuaweiWang/WearableMeasurementSystem).

Musculoskeletal disorders constitute the leading work-related health issue. Mechanical loading of the lower back contributes as a major risk factor and is prevalent in many tasks performed in logistics. The study aimed to compare acute effects of exoskeletons with different functional mechanisms in a logistic task. Twelve young, healthy individuals participated in the study. Five exoskeletons with different functional mechanisms were tested in a logistic task, consisting of lifting, carrying, and lowering a 13 kg box. By using electromyography (EMG), mean muscle activities of four muscles in the trunk were analyzed. Additionally, kinematics by task completion time and range of motion (RoM) of the major joints and segments were investigated. A main effect was found for Musculus erector spinae, Musculus multifidus, and Musculus latissimus dorsi showing differences in muscle activity reductions between exoskeletons. Reduction in ES mean activity compared to baseline was primarily during lifting from ground level. The exoskeletons SoftExo Lift and Cray X also showed ES mean reduction during lowering the box. Prolonged task duration during the lifting phase was found for the exoskeletons BionicBack, SoftExo Lift, and Japet.W. Japet.W showed a trend in reducing hip RoM during that phase. SoftExo Lift caused a reduction in trunk flexion during the lifting phase. A stronger trunk inclination was only found during lifting from the table for the SoftExo Lift and the Cray X. In conclusion, muscle activity reductions by exoskeleton use should not be assessed without taking their designed force paths into account to correctly interpret the effects for long-term injury prevention.

Evaluating exoskeleton actuation methods and designing an effective controller for these exoskeletons are both challenging and time-consuming tasks. This is largely due to the complicated human–robot interactions, the selection of sensors and actuators, electrical/command connection issues, and communication delays. In this research, a test framework for evaluating a new active–passive shoulder exoskeleton was developed, and a surface electromyography (sEMG)-based human-robot cooperative control method was created to execute the wearer’s movement intentions. The hierarchical control used sEMG-based intention estimation, mid-level strength regulation, and low-level actuator control. It was then applied to shoulder joint elevation experiments to verify the exoskeleton controller’s effectiveness. The active–passive assistance was compared with fully passive and fully active exoskeleton control using the following criteria: (1) post-test survey, (2) load tolerance duration, and (3) computed human torque, power, and metabolic energy expenditure using sEMG signals and inverse dynamic simulation. The experimental outcomes showed that active–passive exoskeletons required less muscular activation torque (50%) from the user and reduced fatigue duration indicators by a factor of 3, compared to fully passive ones.

The biological ankle dorsiflexes several degrees during swing to provide adequate clearance between the foot and ground, but conventional energy storage and return (ESR) prosthetic feet remain in their neutral position, increasing the risk of toe scuffs and tripping. We present a new prosthetic ankle intended to reduce fall risk by dorsiflexing the ankle joint during swing, thereby increasing the minimum clearance between the foot and ground. Unlike previous approaches to providing swing dorsiflexion such as powered ankles or hydraulic systems with dissipative yielding in stance, our ankle device features a spring-loaded linkage that adopts a neutral angle during stance, allowing ESR, but adopts a dorsiflexed angle during swing. The ankle unit was designed, fabricated, and assessed in level ground walking trials on a unilateral transtibial prosthesis user to experimentally validate its stance and swing phase behaviors. The assessment consisted of three conditions: the ankle in an operational configuration, the ankle in a locked configuration (unable to dorsiflex), and the subject’s daily use ESR prosthesis. When the ankle was operational, minimum foot clearance (MFC) increased by 13 mm relative to the locked configuration and 15 mm relative to his daily use prosthesis. Stance phase energy return was not significantly impacted in the operational configuration. The increase in MFC provided by the passive dorsiflexing ankle prosthesis may be sufficient to decrease the rate of falls experienced by prosthesis users in the real world.

Standing up using one leg is a challenging task for those with a transfemoral amputation, particularly for elderly users with a low activity level. Active prostheses are generally not accessible to this group and available passive prostheses do not support standing up. This article presents the design and evaluation of the “Energy Restoring Intelligent Knee” (ERiK), which stores energy during sit-down in a pneumatic cylinder and returns it during stand-up. We hypothesized that the system would reduce the time needed to perform transitions and also enable higher load sharing by the prosthetic leg. However, the results of an experimental study with seven participants with transfemoral amputation contradict these hypotheses: the participants could neither move faster nor make more use of the prosthetic leg to share their body weight during transitions. We observed that a major obstacle to the useful functionality of the leg was the absence of ankle dorsiflexion – the foot tended to slip during stand-up initiation, such that only low pre-pressures and therefore support levels could be set. The rather binary action of the pneumatics also complicated movement initiation. The lessons learned from this study may be helpful to those seeking to create better designs in the future.

Passive exosuits have been vastly researched in the past decade for lifting tasks to alleviate the mechanical loading on the spine and reduce the lower back muscle activities in lifting tasks. Despite promising advantages of exosuits, factors such as comfort directly influence the user’s acceptability of such body-worn devices. Exosuits’ routing/anchoring points, which transmit device-to-body forces, remain the leading cause of discomfort among users. In the present study, we sought to investigate the effect of the routing element, that is, the “moment arm,” in altering the device-to-body forces and perceived discomfort. We first presented a simplified human–exosuit model to establish insight into the effect of the moment arm on the device-to-body forces acting at the shoulder (FS) and waist (FW). Further, an experimental investigation was conducted on 10 participants with six different exosuit moment arm configurations (C1, C2, C3, C4, C5, and C6) to investigate their effect on the device-to-body forces, perceived discomfort, and muscle activity using a passive back-assist exosuit emulator in a lifting/lowering task. Configuration C4 was found to be most beneficial in reducing device-to-body forces at the shoulder and waist by up to 44.6 and 22.2%, respectively, during lifting. Subjective scores also comprehended with the device-to-body forces, indicating that C4 produces significantly less discomfort for participants. The outcome of the study illustrates the importance of selecting an appropriate moment arm configuration for passive back support exosuits in alleviating the device-to-body forces and perceived discomfort.

Passive ankle-foot prostheses are light-weighted and reliable, but they cannot generate net positive power, which is essential in restoring the natural gait pattern of amputees. Recent robotic prostheses addressed the problem by actively controlling the storage and release of energy generated during the stance phase through the mechanical deformation of elastic elements housed in the device. This study proposes an innovative low-power active prosthetic module that fits on off-the-shelf passive ankle-foot energy-storage-and-release (ESAR) prostheses. The module is placed parallel to the ESAR foot, actively augmenting the energy stored in the foot and controlling the energy return for an enhanced push-off. The parallel elastic actuation takes advantage of the amputee’s natural loading action on the foot’s elastic structure, retaining its deformation. The actuation unit is designed to additionally deform the foot and command the return of the total stored energy. The control strategy of the prosthesis adapts to changes in the user’s cadence and loading conditions to return the energy at a desired stride phase. An early verification on two transtibial amputees during treadmill walking showed that the proposed mechanism could increase the subjects’ dorsiflexion peak of 15.2% and 41.6% for subjects 1 and 2, respectively, and the cadence of about 2%. Moreover, an increase of 26% and 45% was observed in the energy return for subjects 1 and 2, respectively.

The ability to accurately identify human gait intent is a challenge relevant to the success of many applications in robotics, including, but not limited to, assistive devices. Most existing intent identification approaches, however, are either sensor-specific or use a pattern-recognition approach that requires large amounts of training data. This paper introduces a real-time walking speed intent identification algorithm based on the Mahalanobis distance that requires minimal training data. This data efficiency is enabled by making the simplifying assumption that each time step of walking data is independent of all other time steps. The accuracy of the algorithm was analyzed through human-subject experiments that were conducted using controlled walking speed changes on a treadmill. Experimental results confirm that the model used for intent identification converges quickly (within 5 min of training data). On average, the algorithm successfully detected the change in desired walking speed within one gait cycle and had a maximum of 87% accuracy at responding with the correct intent category of speed up, slow down, or no change. The findings also show that the accuracy of the algorithm improves with the magnitude of the speed change, while speed increases were more easily detected than speed decreases.

Back overuse injuries are a significant problem in the U.S. Army, responsible for nearly a quarter of musculoskeletal injuries. Back exosuits are wearable devices that relieve musculoskeletal strain, make lifting easier, and could potentially reduce Soldier overuse injuries. But published studies have not evaluated exosuits during realistic field operations to assess acceptability to Soldiers. We tested a back exosuit on field artillery Soldiers during a field training exercise. Afterward, Soldiers completed a survey to quantify their satisfaction, intent to use, and performance impact of the exosuit. Feedback was overwhelmingly positive: Approximately 90% of Soldiers reported that exosuits increased their ability to perform their duties, and 100% said that if the exosuit were further developed and made available to them, they would be likely to wear it. These numerical survey results indicated that exosuits can provide a practical and acceptable way to assist lifting and augment physical performance during realistic Army operations without interfering with other duties.