Bed Casting

The bed cast is a simple method for measuring total strain. A length of vinyl tubing, containing freshly mixed casting resin and a heating wire, is hammered into the bed. At freezing temperatures, the catalyzing reaction is effectively halted, so the tube remains flexible. After several days of deformation, the resin is heated and hardened by passing a current through the wire. The stiff tube, now a cast of the deformation to which it has been subjected, is then pulled out. In most cases, the cast retains enough elasticity to survive passage through the borehole undamaged; if the cast should crack, its shape is easily reconstructed.

In our experiments, we use vinyl tubing having an outside diameter of 6.35 mm [0.250 in] and an inside diameter of 4.76 mm [0.1875 in]. The polyester casting resin is doped with the recommended amount of catalyst for hardening at room temperature. The nichrome heating wire has a resistance of 35Ωm⁻¹. Hardening is accomplished by circulating 0.9–1.3 Λ of current through the wire for ∼3 h. This represents a power dissipation of 28–59 Wm⁻¹ into the resin. The nichrome wire is sheathed in teflon “spaghetti” tubing to prevent the vinyl tube from melting. Because the resin is attacked by water, care must be taken to ensure that the instrument is watertight.

Figure 2a shows a cast which was hammered 12 cm into the bed and then catalyzed immediately. As expected, no deformation is evident. The slight curling of the cast was caused by shrinkage of the resin as it set. figure 2 shows a cast which was inserted 7 cm into the undisturbed bed, and left 92 h before heating began. The dashed line in the figure represents the surface of the undisturbed bed material, and the dotted line indicates the estimated location of the ice bed interface (20 cm above the undisturbed material). The distinct double-bend offset near the bottom of the cast suggests that the zone containing the bend was deforming but, because the cast may have extended up into the ice, the bending could be attributed to glacier sliding. During the experiment, the glacier surface above the instrument moved approximately 40 cm.

Fig. 2.

Tracings, from photographs, of Trapridge Glacier bed casts on a 10 cm by 10 cm grid, (a) A bed cast catalyzed and withdrawn immediately after insertion. (b) A bed cast left in the deforming layer for 92 h before removal (the tip was lost upon withdrawal). The dashed line indicates the upper boundary of the undisturbed bed into which the bedcasts were hammered; the dotted line indicates the estimated location of the ice-bed interface.

Two other bed casts were successfully installed in 1987 (a fifth cast was not properly anchored in the bed and detached when the hammer was withdrawn). One. installed to a depth of 12 cm, had a break in its healing circuit and could not be catalyzed. The other, installed to a depth of 35 cm, was held so tightly by the glacier bed that it snapped in two and only the upper 10 cm of the cast was recovered.

Rubber Rod

To ascertain whether strain rate varies with time, we built a rudimentary strain gauge capable of making continuous qualitative strain measurements. The rubber rod consists of a 20 cm length of 6.35 mm [0.250 in] square-section rubber onto which a strain-gauge network is bonded. The rod is sheathed in a glycerin-filled protective vinyl tube. Gauges are bonded on to the faces of the rod near its midpoint and can record flexure along two axes.

Results from 2 d of observation using this instrument confirmed that temporal changes in the strain rate occur (Fig. 3). The experiment ended when excessive strain caused breaks in the strain-bridge wiring. The glacier-surface velocity was approximately 12cm d⁻¹ during the course of the experiment. The axes of strain are labelled down-flow and cross-flow, assuming that the upward-trending record (solid line) represents strain in the direction of ice flow, and the second record (dotted line) represents strain perpendicular to this direction. We believe these assumptions are correct because the physical characteristics of the rod cause it to twist within the vinyl tube so that the bending strain is shifted to one pair of faces. A striking feature of the down-flow strain record is that it is not monotonically increasing. The slope of the curve, which is proportional to strain rate, is occasionally zero or negative. Because deformation counter to the direction of ice flow is unlikely, the negative strain rates suggest sporadic extrusive flow within the deforming layer. Extrusive flow within the layer is not excluded because, unlike the glacier itself, the layer is confined from above and below by rigid boundaries. The glacier forms a rigid upper boundary and non-deforming sediment or bedrock a lower boundary.

Fig. 3.

Results from the 1987 rubber-rod experiment. The vertical scale is in relative strain units, as the device was uncalibrated. The solid line represents strain in the direction of ice flow. The dotted line represents cross-flow strain.

Electrolytic Tilt Sensors

Electrolytic tilt cells operate on the principle that the conductance between two electrodes immersed in an electrolyte is proportional to the total wetted surface area of the electrodes. Λ single-axis electrolytic tilt cell consists of three electrodes partially immersed in an electrolyte Fig. 4). Electrodes may descend from the top of the cell or ascend from the bottom. As the cell is rotated about the plane of the electrodes, the central electrode remains immersed to the same level and the lateral electrodes are dipped in and out of the electrolyte. To make a tilt measurement, the tilt cell is connected to an a.c. bridge containing two reference resistors (a.c. excitation prevents electrode polarization:. The magnitude of the output voltage of the cell is roughly proportional to the tangent of the tilt angle, and the sign determines the tilt direction. A dual-axis tilt cell has five electrodes arranged in a “+” pattern with the central electrode common to both circuits.

Fig. 4.

Schematic diagram of the electrolytic tilt cell and electronics used in the 1988 experiment. The cell is 57 mm long and 16 mm in diameter. An a.c. excited bridge is formed between the cell and two reference resistors. As the cell is tilled, the lateral electrodes dip in and out of the electrolyte and their resistance with respect to the central electrode changes. The bridge imbalance is measured to give the degree and polarity of tilt. For dual axis-tilt sensitivity, a second pair of lateral electrodes is mounted at right-angles to the first pair and Ike central electrode is shared by both circuits.

Our tilt cells have copper electrodes suspended from the top of an acrylic cell. The electrolyte is a weak solution of Alconox, a common laboratory detergent. The space above the electrolyte is filled with naphtha to prevent water infiltration under pressure. When microfractures are etched in the surface of the acrylic by rinsing it for 5s in methanol, novisible meniscus forms between these two fluids. The fluid interface remains horizontal as the cell is tilted. The presence of a meniscus would interfere with accurate measurements of till because the electrodes are in close proximity to the wall of the cell.

Our choice of immiscible fluids represents the best formula picked during a series of desperate in-field tesis. During the 1938 field season, we discovered that the original electrolyte choice — saturated copper-sulphate solution — did not behave properly in the presence of naphtha or any other insulating fluid available to us. We are certain that better choices exist (such as those in commercial devices) and we do not recommend that this electrolyte formulation be used.

Three cells, each 57 mm long and 16 mm in diameter, are assembled into a string at a centre-to-centre spacing of 10 cm. The siring is cased in a protective sheath of heat-shrink tubing, and the lowermost cell is fitted into the insertion lip. Prior to insertion, the cells are calibrated on a special jig. The jig allows a to cell be rotated about its long axis while the tilt of the axis is fixed at various angles. Our cells are calibrated at till angles ranging between 0° and 60° from vertical. For each calibration-tilt angle θ_i , the output voltages from each tilt circuit are tilted, using least squares, to functions of the form

where the subscript i enumerates the discrete tilt angles, A_i are the fitted signal amplitudes at those till angles, B_i are the azimuth offsets, C_i are voltage offsets, ϕ represents the azimuth of the tilt and V is the predicted voltage output. It is important to note that the azimuth ϕ is measured in a local coordinate system where the z axis is aligned with the long axis of the tilt cell; the azimuth is in no way equivalent to orientation in a geographical coordinate system.

A tilt cell consists of two tilt circuits, so each cell has two sets of functions of this form associated with it. For a given tilt angle, the circuits in a perfect cell would have values of Β differing by exactly 90°. In practice, the electrode groups are imperfect and the values of Β differ by roughly 90^e. When the field data are analyzed, a natural cubic spline (Reference Press, Flannery, Teukolsky and VctterlingPress and others, 1986, p. 86) interpolates values of A, Β and C at tilt angles intermediate to those for which calibrations were performed. This transforms the two sets of discrete calibration functions for a specific cell into the continuous system of equations

where the subscripts x and y distinguish the orthogonal tilt circuits. The Newton Raphson method for non-linear systems of equations (Reference Press, Flannery, Teukolsky and VctterlingPress and others, 1986, p. 269) is used to calculate the v alues of θ and ϕ that would give the observed output voltages V_x and V_y . The error on tilt and azimuth for these sensors was estimated by using the calibration data as input to the inversion scheme. The tilt-angle error is ±1° at 0° of tilt, increasing to ±2° at 30° of tilt, and to ±3° at 60° of tilt. The azimuth error is ±5°. Though these errors are large, they are systematic. We believe that the relative error between successive measurements is negligible because the tilt and azimuth records appear smooth. Based on zero relative error, the error in strain rate is 1% at 0° of tilt, increasing to 4% at 30° of tilt and to 20% at 60° of tilt.

On 10 August 1988, an electrolytic tilt-sensor string was hammered 8 cm into the undisturbed bed of Trapridge Glacier. Figure 5 shows the results for 23 d of observation. The data are presented in the raw form generated by applying the calibration functions: the solid lines indicate tilt from vertical and the dotted lines indicate the azimuth of the till with respect to the internal coordinates of the cell. During the course of the experiment, the glacier surface in the study area moved about 10 cm d⁻¹.

Fig. 5.

The 23 d record from the 1988 electrolytic tilt-sensor string. The upper, middle and lower cells are labelled (a), (b) and (c), respectively. Solid lines indicate tilt from vertical (left scale): dotted lines indicate the azimuth of the tilt with respect to the internal coordinates of the cell (right scale). The records from the two lower cells indicate that they were within a deformation Zone that sometimes experienced zero and negative strain rates. The arrows indicate these times. The cartoon below the graphs shows the position of the individual cells within the deforming layer at specific times. Ice movement is to the right.

The data for the lowest two tilt cells indicate an initial net tilt angle of about 45°; this is a surprisingly large value. The deformation instrument is inserted co-axially with the bottom of the borehole, but this borehole had a 3° up-glacier tilt. Some other disturbance caused the tilt cells to “fall over” shortly after the percussion hammer was removed. We believe that the heat-shrink sheath stiffened the instrument sufficiently so that, when slack cable was lowered down the borehole, the instrument was pushed over. Even the bottom cell, which was inserted into undisturbed material, was affected. Evidently, the disturbed layer of the bed was not firm enough to prevent this motion. The rapid onset (within 1 d) of independent cell motion suggests that the disturbed layer solidified quickly, allowing further shear deformation to be recorded.

If we assume that the principal direction of tilt is in the down-flow direction, we can further decompose the net tilt and azimuth values into down-flow and cross-flow components of tilt. Variations in the azimuth of a tilt cell result from three motions: (1) rotation of the tilt cell about its long axis, (2) shear-like movement of the tilt cell in a direction perpendicular to the vertical plane passing through its axis (this will also change the net tilt angle) and (3) pivoting of the tilt cell through a near-vertical orientation. This last movement results in a distinctive 180° shift in azimuth and a sharp dip in the net tilt angle. In the absence of information on the orientation of the tilt cell in a geographical coordinate system, the relative contribution of each of the first two motions to changes in azimuth are unknown. In order to interpret the data, we make the assumption that azimuth changes due to rotation are generally long-term (over several days) and that changes due to shearing are generally short-term (less than 1 d). The basis for this assumption lies in the observation that the azimuth lime series tends to be a slowly varying function upon which fluctuations are superimposed. By attributing the azimuth drift to cell rotation (which has no effect on strain rates), we can isolate the azimuth fluctuations, which in turn are attributed to both rotation and shear. This assumption is of little consequence because altering the partitioning of azimuth change between these two motions has a surprisingly small effect on the computed strain rates. In our analysis, the azimuth drift is removed by subtracting a linear drift function. The decomposition process must also account for the initial orientation of the tilt cell relative to the glacier-flow direction; the initial cross-flow tilt may be non-zero.

The azimuth records shown in Figure 5 show little variation from piece-wise straight lines and, for this sensor string, the dip direction of the hole is aligned with the glacier-flow direction. We conclude that almost all the tilt for this particular data set is in the down-flow direction, so the data separate naturally into down-flow and cross-flow tilts. The component decomposition for these data is not shown because we wish to show the smooth character of the raw data, but the decomposition would show a near-zero cross-flow tilt and a down-flow tilt mimicking the net tilt. Early in the experiment, each of the lower two cells experienced a 180° shift in azimuth associated with a sharp decrease in tilt angle. This suggests that these two cells originally tilted up-glacier; the azimuth shift indicates when each cell pivoted to tilt down-glacier.

It is evident that all the cells quickly reached an orientation outside their calibrated range. Indeed, the uppermost cell seems to have passed the whole experiment resting on its side. Late in the experiment, this cell was tipped over, probably by the glacier pulling on the cable. As with the strain record from the rubber rod, brief intervals of zero and negative strain rate are observed. These are indicated by arrows on the figure.

Leaf-spring Tilt Sensors

The disadvantages of our electrolytic tilt cell are that it has a limited range over which tilt measurements can be made and that the measurement error is large. Special attention must be paid to sealing the cell and care must be taken in choosing a suitable stable electrolyte. These problems are overcome with the leaf-spring sensor illustrated in Figure 6.

Fig. 6.

Schematic diagram of the leaf-spring tilt cell used in the 1989 experiment. The cell is 47 mm long and 16 mm in diameter. As the cell is tilted, the pendulum masses bend the two leaf springs mounted at right-angles to each other. The leaf springs are only sensitive to bending in one direction, so the two pendula respond to tilt along different axes. The bending is measured by strain gauges bonded to the surfaces of the leaf springs.

Two leaf-spring pendula measure the tilt along perpendicular axes. Each leaf spring consists of a small clamped strip of 50.8 μm [0.002 in] spring brass having a mass attached to the free end. A pair of small strain gauges is bonded to the laces of the spring. As the cell tilts, the weight of the mass bends the spring and strains the gauges. The output voltage is roughly proportional to the sine of the tilt angle, so that the tilt angle itself is ambiguous when the cell is tilted more than 90° from vertical.

These cells are 47 mm in length and 16 mm in diameter. Each cell is made of acrylic and is filled with Dow Corning 200 fluid. This inert silicone fluid is non-conductive and non-corrosive, serves to dampen vibration of the masses and thwarts water infiltration (all these characteristics prove necessary). The damping fluid has a kinematic viscosity of 50 cSt (l cSt= l mm² s⁻¹; the centi-Stoke is the cgs unit often used to describe fluids in chemical supply-house catalogues). The pendulum weights are made of split lead shot. The cells are assembled into strings of three having a centre-to-centre spacing of 7.5 cm. The cells are connected using 36 AWG solid copper wires. The strain-bridge circuit is such that eight wires lead up to the surface from the upper cell, six wires connect the upper and middle cells and four wires connect the middle and lower cells. Because the protective heat-shrink sheath created problems in 1988, no sheath was placed over these sensor strings. Some permanent straining of the brass springs was observed to occur during the hammering process, but this shift in the calibration is easily corrected by using tilt recordings made before, during and after the insertion. In future, this problem could be avoided by using a higher-viscosity damping fluid and plastic leaf springs. Certain plastics have a much higher elastic limit than does brass and would accommodate greater strain.

The calibration process for leaf-spring tilt cells is identical to that for electrolytic tilt cells with the exception that the calibration range is extended to 90° of tilt. The processing of in situ deformation data is somewhat different because the Newton Raphson method does not yield a stable inversion. When the field data are analyzed, values θ and ϕ for the cell are computed from Equation 6 using a two-dimensional simplex algorithm (Reference Press, Flannery, Teukolsky and VctterlingPress and others, 1986. p. 289) that minimizes the difference between predicted and observed output voltages. As with the electrolytic tilt cells, the error on tilt and azimuth (or these sensors was estimated by using the calibration data as input to the inversion scheme. The sine of the tilt has a maximum error of °0.005, which translates into a 0.3° error at 0° of tilt, increasing ±0.6 error at 60° of tilt and to ±5° error at 90° of tilt. The azimuth error is ± 4° at 0° of tilt,decreasing to ±1° at 90° of tilt. The error in strain rate is 0.003% at 0° of tilt, increasing to 2% at 60° of tilt.

Two sensor strings were hammered into the glacier bed during the summer of 1989. Unlike our experience in 1988, the initial tilt of these sensors was close to that of their respective insertion angles. Omitting the stiff protective sheath appears to have resulted in instruments that are flexible enough so as not to be forced from their insertion position.Figure 7 shows the down-flow strain-rate data sensed by one of these leaf-spring tilt-cell strings. This string was inserted 20 cm into the undisturbed basal sediments and had an overall length of 27 cm. After the insertion, the instrument cable was lied off with 1.5 m of slack. The signal from all three tilt cells indicates that they lay within actively deforming basal material. Because the insertion depth was not sufficient to place the uppermost cell within solid basal material and, because the cell did not have support from the cable, it must have been supported by the disturbed sediment layer. This sets the minimum thickness of the disturbed layer for this hole at about 10 cm. We estimate that, in general,the thickness of the disturbed layer is 15–25 cm.

Fig. 7.

Sample results from the 1989 leaf-spring tilt-sensor experiment. Tilt records for each of the three tilt cells have been differentiated to give strain rate parallel to ice flow. Strain rates normal to ice flow have been omitted for clarity, but are of comparable magnitude.

These records were produced by performing a decomposition of the raw tilt and azimuth data, as is discussed above. Because the tilt measurements are made with respect to the vertical, we modify Equation 3 to include the basal slope of the glacier β so that

The basal slope in the region surrounding the study area is 7°, as determined by drilling depths.

Cross-flow strain rates are not shown but are of comparable magnitude. This is a surprising result but one we accept because the alternative seems to be unacceptable; if the down-flow/cross-flow decomposition is constrained to prohibit cross-flow strain, then the implied motion of the cells requires back-and-forth rotation about their long axes by as much as 100°. There may be partitioning between cell rotation and cross-flow tilt but the effect on down-flow tilt is slight. Any fraction of cross-flow tilt that is assigned to cell rotation reduces cross-How tilt by a similar fraction and down-flow tilt increases slightly to maintain the correct net tilt.

Strain rates were computed by applying a five-point running first-derivative filter to the strain record (Reference Abramowitz and I. A.Abramowitz and Stegun, 1965, p.914), followed by a Gaussian smoothing filter having a standard deviation of 50 min.

The data have several interesting characteristics: (1) all three records are similar, indicating that each sensor was moving in concert with the others. This may indicate uniform deformation over the 20 cm length of the sensor string, or that the wires connecting the cells were exerting enough tension to keep the sensors aligned with one another. The former explanation is more plausible because we have data from other leaf-spring sensor strings that do not exhibit this synchronism. (2) For each of the three sensors, the average strain rate over the period of the experiment was of the order 10 year⁻¹, whereas the instantaneous strain rate was as large as 400 year⁻¹. (3) Negative and zero strain rates were observed. Though the average down-flow strain rate for each cell was positive, indicating net down-flow strain within the deforming layer, the periods of negative strain rate were frequent. (4) In the second half of the experiment, there was evidence of diurnal synchronization.

Sensor-Scale Effects

When making detailed measurements of deformation within an inhomogeneous material, a fundamental concern is choosing an appropriate scale of observation. If the scale of observation is too small (on the scale of individual clasts in the material), the concept of bulk viscosity becomes meaningless because there is no macroscopic, smooth velocity gradient along which shear stress may be transferred and viscosity defined. Undersized sensors would measure the random wanderings of individual clasts rather than the macroscopic properties of the deforming material. Conversely, if we observe the bedon too large a scale, the deforming layer appears as a single unit with no internal structure.

We expect the deforming layer beneath Trapridge Glacier to be decimeters thick (Reference Boulton and R. C. A.Boulton and Hindmarsh, 1987; Reference ClarkeClarke, 1987), so we want to observe deformation on a scale of centimeters. Were the basal material beneath Trapridge Glacier homogeneous, our 5 cm long tilt sensors would make clear measurements of subglacial strain but this is not the case. A dry-volume fraction analysis of Trapridge Glacier basal material shows that 50% of the clasts are less than 0.25 mm in diameter and that 80% of the clasts are less than 2 cm in diameter Reference ClarkeClarke, 1987). Although these fractions increase once water is added to the system, the size of our tilt sensors is such that they behave as large clasts. There is no alternative but to accept this limitation because any technique for making local deformation measurements will be subject to the same conditions. Tilt cells placed near a clast of similar or larger size will be influenced by the movement of the clast, and Equations (3) and (4), which rely on the homogeneous nature of the basal material, may not be directly applicable.

The Ice-Bed Interface

We cannot observe the insertion procedure directly and must rely on physical constraints and tactile information to infer what is happening at the bottom of the borehole. Our hot-water drill uses a 1.14 mm [0.045 in] diameter jet with a pressure drop of 7–14 MPa [1000–2000 psi] across the nozzle. We believe that hydraulic excavation by the drill loosens material to a depth of several decimeters below the ice bed interface. Evidence for this excavation includes the sediment-laden basal water samples that we obtain shortly after completing a borehole. When the percussion hammer is lowered to the bottom of a borehole, its dead weight exerts a pressure of about 1 MPa on the tip (for comparison, the ice-overburden pressure beneath our study site is 0.64 MPa). This pressure pushes the hammer through the loosened material; the insertion process begins and is measured from the upper surface of the undisturbed bed material. Thus, the upper parts of the instrument may be below the ice-bed interface, even if the insertion depth into the undisturbed material is less than the length of the instrument. Typically, an insertion proceeds quickly for the first 5 cm and then slows down, suggesting that there is a gradation between the disturbed and undisturbed material. Evidence for the existence of the disturbed layer is found in the data and has been discussed above.

Sensor Attitude

The diameter of the percussion hammer is 3.81 cm and, based on our experience with larger subglacial instruments, the diameter of the bottom of a borehole is just over 5 cm. These radial dimensions, in combination with the 2 m length of the percussion hammer, ensure that the hammer fits snugly in the borehole and that the instrument is inserted into the subglacial sediment coaxially with the bottom of the hole. Each of the holes used for bed-deformation experiments was profiled using an inclinometer equipped with dual-axis tilt sensors and a compass. By determining the azimuth of the borehole as it intersects the ice bed interface, we determine the initial azimuth of the bed-deformation instrument relative to the glacier-flow direction. The inclinometer is capable of determining the location of the bottom of a 70 m borehole to within 60 cm. As they reach the bed, our boreholes commonly deviate from vertical by as much as 10–15°.

Sediment Intrusion into the Borehole

After the borehole is completed, several hours typically-pass before the insertion procedure begins. This raises the concern that we may not insert our sensors into subglacial material, but rather into sediment that has squeezed into the borehole. We believe that this possibility can be ruled out because the observed shear-deformation rates exceed, by several orders of magnitude, the ice-deformation rates that would control sediment deformation within an ice-walled hole. Moreover, using similar insertion techniques, we install other types of sensors into subglacial sediment and have unequivocal evidence that these sensors are implanted in bed material rather than extruded sediment. We discuss these two observations in turn.

The basal shear stress beneath Trapridge Glacier is 77 kPa and the basal temperature of Trapridge Glacier in the study area is close to the pressure-melting point (Reference Clarke,, S.G. and ThompsonClarke and others, 1984, Fig. 4, above site 11). Evaluating Glen’s flow law for simple shear

at 0C gives a strain rate of when the shear stress τ = 77kPa, A = 5.3 × 10⁻¹⁵s⁻¹ kPa⁻³, and n = 3 (Reference PatersonPaterson, 1981, p. 39). Assuming Newtonian visco-elastic shear deformation of the form

this strain rate represents a dynamic viscosity of 2 × 10¹³ Pa s. This ice-viscosity value is two orders of magnitude greater than published values of measured or predicted tilt viscosity (Reference Boulton and R. C. A.Boulton and Hindmarsh, 1987,Fig. 7; Reference ClarkeClarke, 1987). Given the low strain rate of the ice, we could not expect to measure strain rates exceeding 100 year⁻¹ within a borehole (see Fig. 7) if the straining of extruded material within a borehole were controlled by-ice deformation.

In 1990, we ran a series of experiments using “drag-spool” instruments. Our intent was to obtain some measure of the sliding rate beneath Trapridge Glacier. A drag spool consists of a multi-turn potentiometer connected to a spooled string. The drag spool is suspended within the ice close to the bed, and measures continuously the length of siring payed out to an anchor in the bed.

The percussion hammer was used to insert three drag-spool anchors in different boreholes to a depth within the undisturbed basal material similar to that of the 1989 deformation instruments. The data indicate that, on average, the anchor points moved away from their respective boreholes at a rate of about 4 cm d⁻¹. This large relative velocity could not persist for many days if the anchor were placed in intruded material. Although these measurements were made at different sub-surface locations and during a different field season than the 1987–89 bed-deformation experiments, surface velocity in each season was about 10 cm⁻¹ and we have not made any changes to our drilling and insertion techniques during this time. Thus, it seems unlikely that basal conditions have undergone dramatic changes between the 1987–90 field seasons. We conclude that the anchors for our bed-deformation instruments are also below the ice bed interface. If the upper parts of a deformation instrument were to extend above the ice bed interface, the data should show this as a rapid increase in tilt to 90° as the tilt cells are drawn out of the borehole and in under the ice; we do not see this behaviour in any of our instruments.

Connecting Wires

The two quantitative instrument designs require that thin wires connect the individual tilt sensors together and that a multi-conductor cable transmit the strain information to the surface.

The main instrument cable freezes to the side of the borehole, and could conceivably pull the entire sensor string out of the bed as the glacier slides forward. By letting slack cable down the hole after the instrument insertion is completed, we alleviate this problem. There is evidence from the 1988 results that this slack-cable technique is sufficient to prevent interference from the cable for several weeks.

The wires connecting the individual sensors are thin enough (36 AWG) so that they cannot prevent the sensor string from bending. Additional cladding, such as the heat-shrink sheath used in 1988, may stiffen the sensor string so that problems arise during the insertion procedure but, if the cladding is omitted, no problems arise. The connecting wires may also act under tension to align the sensors with each other. Any tension effect will become more acute as time passes. There is not much that can be done about this problem, other than using telemetry techniques that do not require wires. W can only be aware that the wires may cause interference.