The electrification of the commuter aircraft is instrumental in the development of novel propulsion systems. The scope of this work aims to explore the design space of a parallel hybrid-electric configuration with an entry into service date of 2030 and beyond and determine the impact of other disciplines on conceptual design, such as components positioning, aircraft stability and structural integrity. Three levels of conceptual sizing are applied and linked with a parametric aircraft geometry tool, to generate the aircraft’s geometry and position the components. Subsequently, the structural optimisation of the wing box is performed, providing the centre of gravity of the components placed inside the wing, that minimise the induced stresses. Furthermore, the stability and trim analysis follow, with the former being highly affected by the positioning of components. Results are compared to a similar aircraft with entry into service technology of 2014 and it is indicated that in terms of block fuel reduction the total electrification benefit increases with the increase of degree of hybridisation, if aircraft mass is kept constant. On the other hand, if battery specific energy is kept constant, similar block fuel reduction is possible with lower hybridisation degrees. The potential for improvement in terms of carbon dioxide emissions and block fuel reduction ranges from 15.73% to 21.44% compared to the conventional aircraft, for levels of battery specific energy of 0.92 and 1.14 kWh/kg respectively. Finally, the component positioning evaluation indicates a maximum weight limitation of 240 kg for the addition of an aft boundary layer ingestion fan to a tube and wing aircraft configuration, without compromising the aircraft static stability.

This paper addresses the potential impact of adverse aircraft-pilot couplings on tiltrotor safety, when a pilot or autopilot attempts to constrain flight dynamics with strong control. The work builds on previously published research on the theory and application of constrained flight to fixed- and rotary-wing aircraft. Tiltrotor aircraft feature characteristics from both types of aircraft and how these determine behaviour in a unique manner is investigated using a FLIGHTLAB simulation model of the XV-15 aircraft. Two different scenarios are explored in detail, using linearised models that reflect the flight-physics of stability for small deviations from trim. First, the control of vertical flight path with longitudinal cyclic pitch and elevator, and the consequences for the stability of the aircraft surge mode and short-period pitch-heave mode. The classical surge-mode instability for flight at speeds below minimum power is shown to apply to the tiltrotor in helicopter mode but alleviated in conversion and airplane modes. The impact on the short–period mode is seen to be a trade-off between the stabilising pitch attitude and destabilising incidence (angle-of-attack) contributions to the flight-path angle. The second example concerns strong control of roll attitude in the presence of adverse aileron-yaw. Here, the yaw-sway motion can be driven unstable, a problem encountered on fixed-wing aircraft with weak weathercock stability, but rare in the rotorcraft world. For both examples, the loss of stability is expressed as the change in sign of effective damping or stiffness stability derivatives. The explanatory theory for these non-oscillatory or low-frequency aircraft-pilot couplings is presented, along with interpretations in terms of handling qualities criteria. The paper also addresses the question of how to translate the findings into a form of aeronautical knowledge useful for the pilot training community.

The high operational cost of aircraft, limited availability of air space, and strict safety regulations make training of fighter pilots increasingly challenging. By integrating Live, Virtual, and Constructive simulation resources, efficiency and effectiveness can be improved. In particular, if constructive simulations, which provide synthetic agents operating synthetic vehicles, were used to a higher degree, complex training scenarios could be realised at low cost, the need for support personnel could be reduced, and training availability could be improved. In this work, inspired by the recent improvements of techniques for artificial intelligence, we take a user perspective and investigate how intelligent, learning agents could help build future training systems. Through a domain analysis, a user study, and practical experiments, we identify important agent capabilities and characteristics, and then discuss design approaches and solution concepts for training systems to utilise learning agents for improved training value.

With an annual growth in travel demand of about 5% globally, managing the environmental impact is a challenge. In 2019, the International Civil Aviation Organisation (ICAO) issued emission reduction targets, including well-to-wake greenhouse gas (GHG) emissions reduced at least 50% from 2005 levels by 2050. This discusses several technologies from an aircraft design perspective that can contribute to achieving these targets. One thing is certain: aircraft will look different in the future. The Transonic Truss-Braced Wing and Flying V configurations are promising significant efficiency improvements over conventional configurations. Electric propulsion, in various architectures, is becoming a feasible option for general aviation and commuter aircraft. It will be a growing field of aviation with zero-emissions flight and opportunities for special missions. Lastly, this paper discusses methods and design processes that include all relevant disciplines to ensure that the aircraft is optimised as a complete system. While empirical methods are essential for initial design, Multidisciplinary Design Optimisation (MDO) incorporates models and simulations integrated in an optimisation environment to capture critical trade-offs. Concurrent design places domain experts in one site to facilitate collaboration, interaction, and joint decision-making, and to ensure all disciplines are equally considered. It is supported by a Collaborative Design Facility (CDF), an information technology facility with connected hardware and software tools for design analysis.

This study proposes a new operational concept of the Point Merge System, called Multi-Arrival Route Point Merge System (MAR-PMS), which is an air traffic control method used to sequence aircraft arrivals in a given terminal control area. The proposed concept enables the additional arrival routes that have an angular difference to each sequencing leg. Furthermore, a time-indexed 0-1 linear programming model is formulated. The obtained results are validated in a real time simulation. The comparison results of PMS and MAR-PMS show that the average reduction of 19% of total flight time, 23% of total flight distance, and 19% in total fuel burned and reduction in CO2 emissions in favor of a proposed concept.

Comprehensive understanding of propulsive jet aerodynamics and aeroacoustics is key to engine design for reduced jet noise and infra-red signature in civil and military aerospace, respectively. Illustrated examples are provided of other aerodynamic/aeroacoustic problems involving jet development, including chevron nozzles, increased jet/wing/flap interference (as fan diameter increases), high acoustic environment (and potentially damaging screech) of supersonic jets on carrier decks and the strongly Three-Dimensional (3D) unsteady flow during the in-ground effect operation of Short Take-Off and Vertical Landing (STOVL) aircraft. To date, laboratory/rig test measurements have primarily been used to identify design solutions; increased use of Computational Fluid Dynamics (CFD) would help achieve cost/time reductions, but Reynolds-Average Navier–Stokes (RANS) CFD with statistical turbulence modelling has proven inadequate for such flows. The scenarios described are far removed from flows used to calibrate model constants, and predictive accuracy demands detailed insight into unsteady flow. Large-Eddy Simulation (LES), whilst computationally more demanding, offers a potential solution. Research undertaken to assess LES capability to address the challenges described is reviewed here. This demonstrates that tremendous progress has been made, indicating that LES can provide sufficiently accurate predictions, representing high value for engineering design. A series of validation studies of increasing realism to practical engineering systems is presented to underpin this conclusion. Finally, areas for further work are suggested to support the combined application of RANS and LES that is probably the optimum way forward.

The research reported in this paper is aimed at the development of a metric to quantify and predict the extent of pilot control compensation required to fly a wide range of mission task elements. To do this, the utility of a range of time- and frequency-domain measures to examine pilot control activity whilst flying hover/low-speed and forward flight tasks are explored. The tasks were performed by two test pilots using both the National Research Council (Canada)’s Bell 412 Advanced Systems Research Aircraft and the University of Liverpool’s HELIFLIGHT-R simulator. Handling qualities ratings were awarded for each of the tasks and compared with a newly developed weighted adaptive control compensation metric based on discrete pilot inputs, showing good correlation. Moreover, in combination with a time-varying frequency-domain exposure, the proposed metric is shown to be useful for understanding the relationship between the pilot’s subjective assessment, measured control activity and task performance. By collating the results from the subjective and objective metrics for a range of different mission task elements, compensation boundaries are proposed to predict and verify the subjective assessments from the Cooper-Harper Handling Qualities Rating scale.

This study focuses on vibration reduction for quadcopters and octocopters with elastic, two-bladed, fixed-speed, variable-pitch rotors through the use of relative rotor phasing. The study defines phase modes such as a pitch phase mode with relative phasing between the front and aft rotors, a roll phase mode with relative phasing between the left and right rotors, and a differential phase mode with relative phasing between the clockwise and counter-clockwise spinning rotors for both the quadcopter and the octocopter, as well as additional higher harmonic phase modes for the octocopter. Parametric studies on individual phase modes indicate that, for the quadcopter in forward flight, the pitch and roll phase modes can almost entirely eliminate the 2/rev vibratory forces (at the aircraft level), but the 2/rev vibratory moments cannot be minimised at the same time. By simultaneously using multiple phase modes, a Pareto front can be generated and a solution selected based on the relative emphasis on force or moment vibration reduction. For the octocopter, it was observed that individual higher harmonic modes (specifically the 2c or 2s modes) could almost entirely eliminate both the 2/rev vibratory forces and moments, simultaneously. Compared with vibration levels in forward flight that might, on average, be expected if the rotors were randomly phased, a 62% reduction of a composite vibration index can be achieved on a quadcopter, and complete elimination of vibration was achievable on an octocopter, with appropriate rotor phasing.

NASA is conducting investigations in Advanced Air Mobility (AAM) aircraft and operations. AAM missions are characterised by ranges below 300 nm, including rural and urban operations, passenger carrying as well as cargo delivery. Urban Air Mobility (UAM) is a subset of AAM and is the segment that is projected to have the most economic benefit and be the most difficult to develop. The NASA Revolutionary Vertical Lift Technology project is developing UAM VTOL aircraft designs that can be used to focus and guide research activities in support of aircraft development for emerging aviation markets. These NASA concept vehicles encompass relevant UAM features and technologies, including propulsion architectures, highly efficient yet quiet rotors, and aircraft aerodynamic performance and interactions. The configurations adopted are generic, intentionally different in appearance and design detail from prominent industry arrangements. Already these UAM concept aircraft have been used in numerous engineering investigations, including work on meeting safety requirements, achieving good handling qualities, and reducing noise below helicopter certification levels. Focusing on the concept vehicles, observations are made regarding the engineering of Advanced Air Mobility aircraft.